8: S–DRUM TARCK (Drum Track) 7–4 : SCAN ZONE
127
7–4 : SCAN ZONE
These settings specify the note and velocity ranges that will use
arpeggiators A and B.
KEY
Bottom Key [C–1...G9]
Top Key [C–1...G9]
Specifies the range of notes (keys) that will use arpeggiator A (B).
Top Key specifies the upper limit, and Bottom Key specifies the
lower limit.
VELOCITY
Bottom Velocity [001...127]
Top Velocity [001...127]
Specifies the range of velocities that will use arpeggiator A (B).
Top Velocity specifies the upper limit, and Bottom Velocity
specifies the lower limit.
Specifies the range of notes (keys) and velocities that will use
arpeggiator A/B.
Tip: You can also set the note and velocity values by keyboard (see
page 13 of the Operation Guide).
Zone Map
This shows the Scan Zone for each arpeggiator, A and B.
V
7–1...4: FUNCTION
•0: Memory Status see page 137
•1: Solo Setting see page 63
•2: Undo see page 137
•3: Create New Song see page 137
•4: Rename Song see page 137
•5: Delete Song see page 137
•6: Copy From Song see page 137
•7:
Copy from Combination
see page 138
•8: Copy from Program see page 139
•9: Load Template Song see page 139
•10: Save Template Song (Save as User Template Song) see
page 140
•11: GM Initialize see page 141
•12: FF/REW Speed see page 142
•13: Set Location (Set Location for Locate Key) see page
142
•14: Copy Arpeggiator see page 150
For more information, please see the “Sequencer: FUNCTION”
section on page 137.
8: S–DRUM TARCK (Drum Track)
8–1: PATTERN
The parameters for the Drum Track function are structured in the
same way as in Combination mode. Assign the Drum Track
program to the desired track 1–16.
However, while a combination triggers the Drum Track pattern on
the global MIDI channel, a song triggers the Drum Track pattern
on the MIDI channel specified by Drum Pattern Input. Normally
you’ll set this to Tch. With the Tch setting, the MIDI channel of the
track selected by Track Select will automatically be used as the
trigger channel.
In Sequencer mode you can use the Drum Track function while
realtime-recording a song track or pattern.
The note-on/off data transmitted by the Drum Track pattern can be
recorded as events in a track.
You can’t use note data from the internal sequencer as a
trigger to start patterns for the Drum Track function.
When you’ve used the Drum Track function with a program or
combination to come up with an idea for a song, you can then use
the Auto Song Setup function to immediately start realtime-
recording (see page 101).
MIDI transmission and reception for the drum track
In Sequencer mode, the Drum Track function transmits and
receives on the following MIDI channels.
Receive: The drum track will receive on the MIDI channel
specified by the Drum Pattern Input setting of each song.
Normally you’ll set this to Tch and use the KROSS’s keyboard to
control the triggering.
Transmit: The drum track will transmit on the MIDI channel
specified by the Drum Pattern Output setting of each song. Set
this to match the MIDI channel of the MIDI track where you’ve
assigned the drum program.
If the track’s Status is BTH, EXT, or EX2, note data etc. of the
Drum Track pattern will be transmitted.
If local control (Local Control On G–MIDI> BASIC) is on,
playing the KROSS's keyboard will not make the internal sound
generator produce sound, nor can the keyboard trigger the
arpeggiator or drum track. However, they can be triggered by note-
on messages from MIDI IN.
Pattern [000, 001...772]
This selects the drum pattern.
Shift [–24...+00...+24]
This transposes the drum pattern in semitone steps. This means
that the instruments played by the pattern will change.
Note: If you've selected a GM drum program for the Drum Track,
you should set this to -12.
Key zone of
arpeggiator A
Key zone of
arpeggiator B
Key zone of
arpeggiator B
Velocity zone of
arpeggiator A
Preset/User No. Contents
000 Off
001...772 Preset drum patterns
Pattern
Bottom Top
To Next Page
Loading...
