Single size effects 095: Tape Echo
269
095: Tape Echo
This effect simulates a tape echo unit with three playback heads.
The distortion and tonal change typical of magnetic tape are also
reproduced.
Tap1 Delay [ms]
Source
Amount
Tap2 Position [%]
Tap3 Position [%]
The delay time for Tap 2 and 3 is specified as a proportion (%)
relative to “Delay (Tap1).” Even if you use dynamic modulation to
control “Delay (Tap1),” Tap 2 and 3 will change at the same
proportion.
Feedback Amount
Feedback Level
The feedback output from Tap 1, 2, and 3 is mixed according to the
“Feedback Amount,” and then the final amount of feedback is
specified by “Feedback Level.”
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Base Note ← ...
Selects the type of
notes to specify the
delay time for the
panning speed p.223
Times ← x1...x32
Sets the number of
notes to specify the
delay time for the
panning speed p.223
Pan Depth Pan Depth 0...100
Sets the panning
width
Src Source Off...Tempo
Selects the
modulation source
for the panning width
Amt Amount –100...+100
Set the modulation
amount of the
panning width
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Paramter Value Explanation
Tap1 [ms]
Tap1
Delay [ms]
0...539
Sets the delay time
(tap1) p.270
Src Source Off...Tempo
Selects the
modulation source of
the delay time p.270
Amt Amount
–2700...
+2700
Sets the modulation
amount of delay time
p.270
Tap2 [%]
Tap2
Position [%]
0...100
Sets the position of
Tap 2 relative to the
Tap 1 delay time the
depth of pitch
variation
p.270
Tap3 [%]
Tap3
Position [%]
0...100
Sets the position of
Tap 3 relative to the
Tap 1 delay time the
depth of pitch
variation
p.270
Feedback
Feedback
Level
0...100
Sets the amount of
feedback for Taps 1, 2,
and 3 p.270
Src Source Off...Tempo
Selects the
modulation source of
feedback amount
Amt Amount –100...+100
Sets the feedback
amount
Saturation ← 0...100
Sets the distortion
amount
HiDamp[%]
High Damp
[%]
0..
.100
Sets the damping
amount in the high
range
LoDamp[%]
Low Damp
[%]
0...100
Sets the damping
amount in the low
range
Wah Flatter
D
-mod
Tap2/3
Position
+
Tape
Saturation
Left
Right
Wet / Dry
Trim
PanLevel
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Feedback
Feedback Amt
High / Low DampPre Tone
Delay
(1)
(2)
(3)
Delay Time
Tap1 Lvl Tap1 Level 0...100
Sets the Tap1 output
level
Pan ← L, 1...99, R
Sets the stereo image
of tap1
FB Amt
Feedback
Amount
–100...+100
Sets the Tap1
feedback amount
p.270
Tap2 Lvl Level 0...100
Sets the Tap2 output
level
Pan ← L, 1...99, R
Sets the stereo image
of tap2
FB Amt
Feedback
Amount
–100...+100
Sets the Tap2
feedback amount
p.270
Ta3 Lvl Level 0...100
Sets the Tap3 output
level
Pan ← L, 1...99, R
Sets the stereo image
of tap3
FB Amt
Feedback
Amount
–100...+100
Sets the Tap3
feedback amount
p.270
Input Trim ← 0...100 Sets the input gain
Pre Tone ← 0...100
Sets the tone of the
input
Wow [Hz]
Wow Flutter
[Hz]
0.02...1.00
Sets the frequency
where pitch variation
will occur
Wow Depth Depth 0...100
Sets the depth of
pitch variation
Wet/Dry ←
Dry,
1 : 99...99 : 1,
Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
To Next Page
Loading...
Need help?
General
