Single size effects 101: St.BPM Mtap Delay (Stereo BPM Multitap Delay)
273
Time Over? L, R
You can set the delay time up to 2,730 msec. If the delay time
exceeds this limit, the error message “OVER!” appears in the
display. Set the delay time parameters so that this message will not
appear. “Time Over?” is only a display parameter.
101: St.
BPM Mtap Delay (Stereo BPM
Multitap Delay)
This is a stereo multi-tapped delay that lets you set the delay time
to match the tempo of the song.
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Paramter Value Explanation
Mode ←
Normal,
Cross
Feedback,
Cross Pan1,
Cross Pan2
Switches the left and
right delay routing
p.267
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.272
T.Over 1?
Tap1 Delay
Time Over?
---, OVER!
Displays an error
message when the
delay time for Tap1
exceeds the upper
limit p.273
T.Over 2?
Tap2 Delay
Time Over?
---, OVER!
Displays an error
message when the
delay time for Tap2
exceeds the upper
limit
p.273
T1 Dly Note
Tap1 Base
Note
...3
Selects the type of
notes to specify the
delay time for Tap1
p.272
T1 Times Tap1 Times x1...x32
Sets the number of
notes to specify the
delay time for Tap1
p.272
T1 Lvl Tap1 Level 0...100
Sets the Tap1 output
level
p.267
T2 Dly Note
Tap2 Base
Note
...3
Selects the type of
notes to specify the
delay time for Tap2
p.272
T2 Times Tap2 Times x1...x8
Sets the number of
notes to specify the
delay time for Tap2
p.272
Fback(T2)
Feedback
(Tap2)
–100...+100
Sets the Tap2
feedback amount
Src Source Off...Tempo
Selects the
modulation source of
the Tap2 feedback
amount
Amt Amount –100...+100
Sets the modulation
amount of the Tap2
feedback amount
HiDamp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range p.266
LoDamp[%]
Low Damp
[%]
0...100
Sets the damping
amount in the low
range p.266
Tempo
BPM
BPM
Base Note x Times
Base Note x Times
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Input Level D-mod
Input Level D-mod
High Damp
Low Damp
High Damp
Low Damp
Delay
Delay
Feedback
Tap1 Level
Mode
Mode
(1)
(2)
(1)
(2)
Tap1=(1)
Tap2=(2)
InpLvl Dmod
Input Level
Dmod [%]
–100...+100
Sets the modulation
amount of the input
level p.261
Src Source Off...Tempo
Selects the
modulation source
for the input level
p.261
Spread ← –100...+100
Sets the width of the
stereo image of the
effect sound
p.266
Src Source Off...Tempo
Selects the
modulation source of
the effect sound’s
stereo image width
Amt Amount –100...+100
Sets the modulation
amount of the effect
sound’s stereo image
width
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
To Next Page
Loading...
Need help?
General
