Effect Guide
278
113: Early Reflections
This effect is only the early reflection part of a reverberation
sound, and adds presence to the sound. You can select one of the
four decay curves.
Type
This parameter selects the decay curve for the early reflection.
114: P4EQ - Mt.Delay (
Parametric 4-
Band EQ - Multitap Delay)
This effect combines a mono four-band parametric equalizer and a
multitap delay.
Paramter Value Explanation
Type ←
Sharp, Loose,
Modulated,
Reverse
Selects the decay
curve for the early
reflection p.278
Times[ms] ER Time [ms] 10...420
Sets the time length
of early reflection
PreDl[ms]
Pre Delay
[ms]
0...100
Sets the time taken
from the original
sound to the first
early reflection
PreEQ Trim Pre EQ Trim 0...100
Sets the input level of
EQ applied to the
effect sound
Pre LEQ Fc
Low EQ
Frequency
Low,
Mid-Low
Selects the cutoff
frequency (low or
mid-low) of the low-
range equalizer
Pre HEQ Fc
High EQ
Frequency
High,
Mid-High
Selects the cutoff
frequency (high or
mid-high) of the
high-range equalizer
LEQ [dB]
Low EQ Gain
[dB]
–15.0...+15.0
Sets the gain of the
Low EQ
HEQ [dB]
High EQ
Gain [dB]
–15.0...+15.0
Sets the gain of the
High EQ
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
EQ Trim
+
EQ Trim
Pre Delay
Early Reflections
LEQ HEQ
Sharp
Loose
Modulated
Early Reflections - Type
Reverse
Dry
Pre Delay
ER Time
Paramter Value Explanation
Parametric 4-Band EQ
E Trim Trim 0...100
Sets the parametric
EQ input level
E1 F[Hz]
Band1
Cutoff [Hz]
20...1.00k
Sets the center
frequency of Band 1
Q Band1 Q 0.5...10.0
Sets the bandwidth of
Band 1 p.221
G[dB]
Band1
Gain [dB]
–18...+18
Sets the gain of Band
1
E2 F[Hz]
Band2
Cutoff [Hz]
50...5.00k
Sets the center
frequency of Band 2
Q
Band2
Cutoff [Hz]
0.5...10.0
Sets the bandwidth of
Band 2 p.221
G[dB]
Band2
Cutoff [Hz]
–18...+18
Sets the gain of Band
2
E3 F[Hz]
Band3
Cutoff [Hz]
300...10.00k
Sets the center
frequency of Band 3
Q Band3 Q 0.5...10.0
Sets the bandwidth of
Band 3 p.221
G[dB]
Band3
Gain [dB]
–18...+18
Sets the gain of Band
3
E4 F[Hz]
Band4
Cutoff [Hz]
500...20.00k
Sets the center
frequency of Band 4
Q Band4 Q 0.5...10.0
Sets the bandwidth of
Band 4 p.221
G[dB]
Band4
Gain [dB]
–18...+18
Sets the gain of Band
4
Multitap Delay
D T1[ms]
Tap1
Time [ms]
0.0...549.0
Sets the Tap1 delay
time
Tap1 Level ← 0...100
Sets the Tap1 output
level
p.267
D T2 [ms]
Tap2
Time [ms]
0.0...549.0
Sets the Tap2 delay
time
Fback(T2)
Feedback
(Tap2)
–100...+100
Sets the Tap2
feedback amount
HiDamp [%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range
D W/D [Dly]Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Se
ts the multitap
delay effect balance
Src [Dly]Source Off...Tempo
Selects the Wet/Dry
modulation source
for the multitap delay
Amt [Dly]Amount –100...+100
Sets the Wet/Dry
modulation amount
for the multitap delay
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Trim
+
Parametric 4Band EQ Multitap Delay
Feedback
High Damp
Delay
(2)
(1)
Mt.Dly Wet / Dry
To Next Page
Loading...
