Single size effects 065: Vintage Chorus
253
L Pre Delay [ms]
R Pre Delay [ms]
Setting the left and right delay time individually allows you to
control the stereo image.
065: Vintage Chorus
This models a famous chorus unit that was built into a guitar amp.
Although it does not provide a chorus and vibrato select switch,
you can use the “Wet/Dry” and “Bus” settings to produce their
effect. The “Speed,” “Depth,” and “Manual” parameters allow an
even wider range of sounds than the original unit.
Wet/Dry
Output Mode
For the master effects, “Wet/Dry” adjusts the output level of the
effect sound.
When “Output Mode” is Mono, L and R will output the same
vibrato effect. Normally, you’ll produce a chorus effect by
adjusting the return level to mix the processed sound with the
direct sound. If you turn “Bus” Off and adjust the settings so that
none of the direct sound is mixed in, a vibrato effect will be
produced.
If “Output Mode” is Stereo (L-Dry & R-Wet), the direct sound will
be panned to L, and the effect sound will be panned to R for
output. Normally, you’ll mix the direct sound and effect sound by
adjusting the return level, applying chorus only to the R channel,
and producing a stereo effect that’s spread to the left and right. If
you turn “Bus” Off, pan the direct sound and effect sound to the
left and right, and output them from stereo speakers, the effect
sound and direct sound will be panned in stereo, producing a clear
and spacious chorus effect.
066: Black Chorus
This models a Danish-made stereo chorus + pitch modulator &
flanger. Although this effect was originally intended for guitar, it
was also used by numerous keyboard players. Used with electric
piano, it produces a distinctive tone.
Mode
Intensity
Increasing the “Intensity” value will strengthen the modulation
effect. This controls the effect, direct, and feedback values. The
values that are controlled will depend on the “Mode” setting.
HEQ [dB]
High EQ
Gain [dB]
–15.0...+15.0
Sets the gain of the
High EQ
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dry input
p.226
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Paramter Value Explanation
Speed [Hz] ← 0.10...10.0 Sets the speed of LFO
Depth ← 0...100
Sets the modulation
depth
Manual ← 1...100
Sets the sweep
frequency
Out Mode
Output
Mode
0, 1
Sets the outpu mode
0: Mono
1: ST (L-D& R-W)
Wet/Dry ←
Dry, 1:99 ...
99:1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100 ... +100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Chorus
LFO
Output Mode
Mono
Stereo
(L-D&R-W)
Paramter Value Explanation
Speed [Hz] ← 0.10...10.0 Sets the LFO speed
Width ← 0...2
Sets the LFO
modulation depth
Mode ←
Chorus
Pitch Mod
Flanger
Select a mode
Intensity ← 1...100
Sets the intensity of
LFO modulation
Input Gain ← 1...1000 Sets the input gain
Out Mode
Output
Mode
0, 1
Select a output mode
0: Mono
1: Stereo
Wet/Dry ←
Dry, 1:99 ...
99:1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100 ... +100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Chorus
LFO
Input Gain
Mode & Intensity
Mono
Stereo
Output Mode
-
+
+
+
To Next Page
Loading...
