Effect Guide
262
082: P4EQ - Cho/Flng (
Parametric 4-
Band EQ - Chorus/Flanger)
This effect combines a mono four-band parametric equalizer and a
chorus/flanger.
083: Comp - Cho/Flng (Compressor
- Chorus/Flanger)
This effect combines a mono compressor and a chorus/flanger.
You can change the order of the effects.
Output Mode
Routing
When Wet Invert is selected, the right channel phase of the chorus/
flanger effect sound is inverted. This creates pseudo-stereo effects
and adds spread.
However, if a mono-input type effect is connected after this effect,
the left and right sounds may cancel each other, eliminating the
chorus/flanger effects.
When “Routing” is set to Flanger→Comp, “Output Mode” will be
set to Normal.
Paramter Value Explanation
Parametric 4-Band EQ
E Trim Trim 0...100
Sets the parametric
EQ input level
E B1 F[Hz]
Band1
Cutoff [Hz]
20...1.00k
Sets the center
frequency of Band 1
Q Band1 Q 0.5...10.0
Sets the bandwidth of
Band 1 p.221
Gain[dB]
Band1
Gain [dB]
–18...+18
Sets the gain of Band
1
E B2 F[Hz]
Band2
Cutoff [Hz]
50...5.00k
Sets the center
frequency of Band 2
Q Band2 Q 0.5...10.0
Sets the bandwidth of
Band 2 p.221
Gain[dB]
Band2
Gain [dB]
–18...+18
Sets the gain of Band
2
E B3 F[Hz]
Band3
Cutoff [Hz]
300...10.00k
Sets the center
frequency of Band 3
Q Band3 Q 0.5...10.0
Sets the bandwidth of
Band 3 p.221
Gain[dB]
Band3
Gain [dB]
–18...+18
Sets the gain of Band
3
E B4 F[Hz]
Band4
Cutoff [Hz]
500...20.00k
Sets the center
frequency of Band 4
Q Band4 Q 0.5...10.0
Sets the bandwidth of
Band 4 p.221
Gain[dB]
Band4
Gain [dB]
–18...+18
Sets the gain of Band
4
Chorus/Flanger
F LFO[Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO
LFO
LFO
Waveform
Tri (Triangle),
Sine
Selects the LFO
Waveform
F Depth Depth 0...100
Sets the depth of LFO
modulation
Dly[ms]
Delay Time
[ms]
0.0...110.0 Sets the delay time
F.back Feedback –100...+100
Sets the feedback
amount p.257
F Wet/Dry
[Cho/Fln]
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the effect
balance of the
chorus/flanger
p.226, p.257
Src
[Cho/Fln]
Source
O
ff...Tempo
Selects the Wet/Dry
modulation source
for the chorus/flanger
Amt
[Cho/Fln]
Amount
–100...+100
Sets the Wet/Dry
modulation amount
for the chorus/flanger
F Out Mode
Output
Mode
Normal,
Wet Invert
Selects the output
mode for the chorus/
flanger p.253
Wet/Dry ←
-Wet...-1:99,
Dry,
1:99...Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Trim
+
Parametric 4Band EQ
Chorus/Flanger
Wet / Dry
Chorus/Flanger
Feedback
LFO: Tri / Sine
Cho/Flng Wet / Dry
Normal
Wet Invert
Output Mode
+
–
Paramter Value Explanation
Compressor
C Sens Sensitivity 1...100
Sets the sensitivity
p.217
C Attack Attack 1...100
Sets the attack level
p.217
Out Level Output Level 0...100
Sets the compressor
output level p.217
C EQ Trim ← 0...100
Sets the EQ input
level
C LEQ [dB]
C Low EQ
Gain [dB]
–15...+15
Sets the gain of Low
EQ
HEQ [dB]
High EQ
Gain [dB]
–15...+15
Sets the gain of High
EQ
Chorus/Flanger
F LFO[Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO
LFO
LFO
Waveform
Tri (Triangle),
Sine
Selects the LFO
Waveform
F Depth Depth 0...100
Sets the depth of LFO
modulation
Dly [ms]
Delay Time
[ms]
0.0...109.0 Sets the delay time
F.back Feedback –100...+100
Sets the feedback
amount p.257
F Wet/Dry
[Cho/Fln]
Wet/Dry
–Wet...
–1 : 99, Dry,
1 : 99...Wet
Sets the effect
balance of the
chorus/flanger
p.226, p.257
Src
[Cho/Fln]
Source
Off...Tempo
Selects the Wet/Dry
modulation source
for the chorus/flanger
Amt
[Cho/Fln]
Amount
–100...+100
Sets the Wet/Dry
modulation amount
for the chorus/flanger
F Out Mode
Output
Mode
Normal,
Wet Invert
Selects the output
mode for the chorus/
flanger p.263
Routing ←
Comp→
Flanger,
Flanger→
Comp
Switches the order of
the compressor and
chorus/flanger p.263
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dr
y input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
Routing
Compressor
Chorus/Flanger
Chorus/Flanger
Feedback
LFO: Tri / Sine
Cho/Flng Wet / Dry
Normal
Wet Invert
Output Mode
–
+
LEQ HEQ
EQ Trim
Comp
Output Level
Envelope - Control