Korg KROSS - Foot

2: G–INPUT/CTRL 2–2: FOOT
165
2–2: FOOT
Foot Switch Assign [List of Foot Switch Assign]
Selects the function that will be controlled by a pedal switch (such
as the optional Korg PS-1 or PS-3) connected to the
ASSIGNABLE SWITCH jack.
For a complete list of possible assignments, please see “MIDI
transmission when the KROSS’s controllers are used” on
page 307.
Foot Pedal Assign [List of Foot Pedal Assign]
Selects the function that will be controlled by a foot volume pedal
(XVP-10, XVP-20 or EXP-2 option [sold separately]) connected
to the ASSIGNABLE PEDAL jack.
For a complete list of possible assignments, please see “Foot
Switch Assign List” on page 301.
Damper Polarity [(–) KORG Standard, (+)]
Set this to match the polarity of the Korg damper pedal that’s
connected to the DAMPER jack. If the polarity does not match,
using the damper pedal will not produce the correct result. If no
damper pedal is connected, set this to (–) KORG Standard.
(–) KORG Standard: Use this setting for “open-type” damper
pedals, such as the optional Korg DS–1H.
(+): Use this setting for “closed-type” pedals.
Foot Switch Polarity [(–) KORG Standard, (+)]
Set this to match the polarity of the Korg footswitch that’s
connected to the ASSIGNABLE SWITCH jack. If the polarity
does not match, using the damper pedal will not produce the
correct result. If no damper pedal is connected, set this to (–)
KORG Standard.
(–) KORG Standard: Use this setting for “open-type”
footswitches, such as the optional Korg PS–1 or PS-3.
(+): Use this setting for “closed-type” pedals.
2–3: CC (MIDI CC# Assign)
Here you can assign control change messages to the ARP button
On/Off and to MOD [GATE], [VEL], and [SWING].
When you use the ARP button or MOD [GATE], [VEL], or
[SWING], the assigned control change message will be
transmitted from the MIDI OUT connector.
The assigned control change messages can also be received from
an external MIDI device connected to the MIDI IN connector, and
used to control the corresponding arpeggiator.
The default settings of each parameter are as shown in the display
above.
ARP Controllers MIDI Out [Control Change, SysEx Change]
Here you can specify the MIDI messages that are transmitted when
you operate the arpeggiator's MOD [GATE], [VEL], and
[SWING].
Control Change: When you operate the ARP button, MOD
[GATE], [VEL], or [SWING], the MIDI control change messages
that are specified in the G-INPUT/CTRL> CC page are
transmitted.
SysEx Change: When you operate the ARP button, MOD
[GATE], [VEL], or [SWING], system exclusive parameter change
messages are transmitted to convey the button and arpeggiator's
on/off status and the state of Gate, Velocity, and Swing.
(SW) [ARP (ON/OFF)] [Off, 000...119]
Assigns a control change message sent by the ARP button. The
default setting is CC#14.
(ARP CONTROL) [GATE] [Off, 000...119]
Assigns a control change message to MOD [GATE]. The default
setting is CC#22.
(ARP CONTROL) [VELOCITY] [Off, 000...119]
Assigns a control change message to MOD [VELOCITY]. The
default setting is CC#23.
(ARP CONTROL) [SWING] [Off, 000...119]
Assigns a control change message to MOD [SWING]. The default
setting is CC#24.
V 2–1...3: FUNCTION
•0: Write Global Setting see page 176
For more information, please see the “Global, Media:
FUNCTION” section on page 176.