Effect Guide
288
D11: Multitap Cho/Delay (Multitap
Chorus/Delay)
This effect has six chorus blocks with different LFO phases. You
can produce a complex stereo image by setting a different delay
time and depth for each block. You can control the delay output
level via a modulation source.
Status
These parameters set the output status of each Tap.
Always On: Output is always on. (No modulation)
Always Off: Output is always off. (No modulation)
On→Off (dm): Output level is switched from on to off depending
on the modulation source.
Off→On (dm): Output level is switched from off to on depending
on the modulation source.
Combining these parameters, you can change from 4-phase chorus
to two-tap delay by crossfading them gradually via the modulation
source during a performance.
Panning Preset
This parameter selects combinations of stereo images of the tap
outputs.
Paramter Value Explanation
Tap1 [ms]
Tap1
Delay (000)
[ms]
0...650
Sets the Tap1 (LFO
phase=0 degrees)
delay time
Dep Tap1 Depth 0...30
Sets the Tap1 chorus
depth
Status Tap1 Status
Always On,
Always Off,
On→Off ,
Off→On
Selects on, off, or
modulation source
for the control of Tap1
output
p.288
Tap2 [ms]
Tap2
Delay (180)
[ms]
0...650
Sets the Tap2 (LFO
phase=180 degrees)
delay time
Dep Tap2 Depth 0...30
Sets the Tap2 chorus
depth
Status Tap2 Status
Always On,
Always Off,
On
→
Off (Dm),
Off
→
On (Dm)
Selects on, off, or
modulation source
for the control of Tap2
output
p.288
Tap3 [ms]
Tap3
Delay (060)
[ms]
0...2000
Sets the Tap3 (LFO
phase=60 degrees)
delay time
Dep Tap3 Depth 0...30
Sets the Tap3 chorus
depth
Status Tap3 Status
Always On,
Always Off,
On→Off
(Dm),
Off→On
(Dm)
Selects on, off, or
modulation source
for the control of Tap3
output
p.288
Tap4 [ms]
Tap4
Delay (240)
[ms]
0...2000
Sets the Tap4 (LFO
phase=240 degrees)
delay time
Dep Tap4 Depth 0...30
Sets the Tap4 chorus
depth
Status Tap4 Status
Always On,
Always Off,
On→Off
(Dm),
Off→On
(Dm)
Selects on, off, or
modulation source
for the control of Tap4
output
p.288
Tap5 [ms]
Tap5
Delay (120)
[ms]
0...2000
Sets the Tap5 (LFO
phase=120 degrees)
delay time
Dep Tap5 Depth 0...30
Sets the Tap5 chorus
depth
Status Tap5 Status
Always On,
Always Off,
On→Off
(Dm),
Off→On
(Dm)
Selects on, off, or
modulation source
for the control of Tap5
output
p.288
Tap6 [ms]
Tap6
Delay (300)
[ms]
0...2000
Sets the Tap1 (LFO
phase=300 degrees)
delay time
Dep Tap6 Depth 0...30
Sets the Tap6 chorus
depth
Left
Right
Feedback
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
+
LFO: Triangle
0 [degree]
180 [degree]
60 [degree]
240 [degree]
120 [degree]
300 [degree]
Tap1 Delay
Tap2 Delay
Tap3 Delay
Tap5 Delay
Tap6 Delay
Tap4 Delay
D
-mod
On/Off Control
Panning Preset
Status Tap6 Status
Always On,
Always Off,
On→Off
(Dm),
Off→On
(Dm)
Selects on, off, or
modulation source
for the control of Tap6
output
p.288
LFO [Hz]
LFO Freq
[Hz]
0.02...13.00
Sets the speed of the
LFO
Pan Preset
Panning
Preset
1 : L 1 2 3 4 5 6 R
2 : L 135 246 R
3 : L 1 3 5 2 4 6 R
4 : L 1 4 5 6 3 2 R
Selects the stereo
panning pattern for
each tap
p.288
Feedback
Tap1
Feedback
–100...+100
Sets the Tap1
feedback amount
Src Source Off...Tempo
Selects the
modulation source
for the Tap output
level, feedback
amount, and effect
balance
Amt Amount –100...+100
Sets the modulation
amount of Tap1
feedback amount
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
To Next Page
Loading...
