Effect Guide
228
E.g.: When “Voice Top”=A, “Voice Center”=I, and “Voice
Bottom”=U:
If Sweep Mode is Dmod, and P.Bend is selected as the modulation
source, moving the pitch bend wheel from the farthest position
toward yourself will make the voice change through the ranges
“a,” “i,” and “u.”
If Sweep Mode is set to LFO, the sound will change cyclically
from “a” to “i,” “u,” “i,” then “a.”
Formant Shift
This parameter adjusts the frequency level where the effect is
applied. If you wish to apply the effect to a higher-range sound, set
this parameter to a higher value; to apply the effect to a lower-
range sound, set this to a lower value.
Resonance
This parameter sets the intensity of resonance for the voice pattern.
A larger value will add more character to the sound.
018: St. Decimator (Stereo
Decimator)
This effect creates a rough sound like a cheap sampler by lowering
the sampling frequency and data bit length. You can also simulate
noise unique to a sampler (aliasing).
+ Max
Zero
D
-mod
– Max
Voice Bottom Voice Center Voice Top
U
I
A
A
O
E
P.Bend
M.Whl #1
etc…
Zero
+ Max
Talking Modulator Control
Paramter Value Explanation
Pre LPF Pre LPF Off, On
Selects whether the
harmonic noise caused
by a decrease in
sampling frequency is
generated or not p.229
HiDamp[%]
High Damp
[%]
0...100
Sets the ratio of cut of
the high range
Fs [Hz]
Sampling
Freq [Hz]
1.00k...
48.00k
Sets the sampling
frequency
Src Source Off...Tempo
Selects the
modulation source of
the sampling
frequency
Amt Amount
–48.00k...
+48.00k
Sets the modulation
amount of the
sampling frequency
LFO Depth Depth 0...100
Sets the depth of the
sampling frequency
LFO modulation
Src Source Off...Tempo
Selects the LFO
modulation source of
the sampling frequency
Amt Amount –100...+100
Sets the LFO
modulation amount of
the sampling frequency
LFO [Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO
Src Source Off...Tempo
Selects a modulation
source for LFO speed
Amt Amount
–20.00...
+20.00
Sets the modulation
amount of LFO speed
MIDI Sync
BPM/MIDI
Sync
Off, On
When this is on, the LFO
speed is set by BPM,
Base Note, and Times,
instead of Frequency
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–300
sets the tempo
manually for this
individual effect
Base Note ← ...
Selects the type of
notes that specify the
LFO speed
Times ← x1...x32
Sets the number of
notes that specify the
LFO speed
Bit Reso
Resolution
[bit]
4...24
Sets the data bit
length p.229
Out Level Output Level 0...100
Sets the output level
p.229
Src Source Off...Tempo
Selects the
modulation source
for the output level
Amt Amount –100...+100
Sets the modulation
amount of the output
level
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Pre LPF
Pre LPF
High Damp Output Level
High Damp Output Level
Sampling Frequency
Decimator
Decimator
D
-mod
LFO
Resolution
Resolution
To Next Page
Loading...
