1: G–MIDI 1–3 FILTER
163
1–3 FILTER
Enable Program Change [Off, On]
On (checked): Program changes will be transmitted and received.
In Program mode (PROG> MAIN), the program will be switched
when a program change message is received on the global MIDI
channel specified by MIDI Channel (G–MIDI> BASIC). When
you switch programs, a program change message will be
transmitted on the global MIDI channel.
In Combination mode (COMBI> MAIN), the combination will be
switched when a program change message is received on the
global MIDI channel. However, it is possible to set the Enable
Combination Change parameter so that the combination is not
switched. When a program change is received on the channel
specified for each timbre by MIDI Channel (C–TIMBRE>
MIDI), the program of that timbre will be switched. However, the
program changes for each timbre will be affected by the setting of
the Enable Program Change parameter (C–MIDI FILTER> 1).
When you switch combinations, a program change message will
be transmitted on the global MIDI channel, and also transmitted
simultaneously on the channel of timbres whose Status (COMBI>
PROG) is set to EXT or EX2.
In Sequencer mode, incoming program change messages on a
channel that corresponds to a track where the Status (COMBI>
PROG) is set to INT or BTH will switch programs on that track.
When you select a song or play back sequencer data, program
changes will be transmitted on the channels of tracks whose Status
is set to BTH, EXT, or EX2 (see “Track MIDI Out” on page 162).
Off (unchecked): Program changes will not be transmitted or
received.
Bank Select [Off, On]
On (checked): The Bank Select control change message will be
transmitted together with program change messages. This is valid
when Enable Program Change is checked.
Off (unchecked): Bank Select messages will not be transmitted or
received.
When recording on the internal sequencer, bank select messages
will be recorded regardless of this setting. However for playback,
this setting will apply.
Combination Change [Off, On]
On (checked): When in COMBI>MAIN, an incoming program
change message on the global MIDI channel set by MIDI
Channel (G–MIDI> BASIC) will switch combinations.
This is valid when Enable Program Change is checked.
An incoming program change on a channel other than the global
MIDI channel will switch the program of any timbre that matches
that MIDI channel.
Off (unchecked): An incoming program change message on the
global MIDI channel will switch the program of any timbre where
the MIDI Channel (C–TIMBRE> MIDI) matches the global
MIDI channel. The combination will not be switched.
The program changes for each timbre will be affected by the
setting of the Enable Program Change parameter (C–MIDI
FILTER> 1).
Enable After Touch [Off, On]
On (checked): MIDI aftertouch messages will be transmitted and
received.
Off (unchecked): MIDI aftertouch messages will neither be
transmitted nor received.
This setting has no effect when you use the internal sequencer to
playback sequence data that was recorded with aftertouch data;
i.e., aftertouch will be transmitted via MIDI.
Performing on the KROSS’s keyboard will transmit neither
channel aftertouch nor polyphonic aftertouch. However, since the
KROSS does support aftertouch as an Alternate Modulation
Source (AMS), it can receive aftertouch to control.
Enable Control Change [Off, On]
On (checked): Control change messages will be transmitted and
received.
Off (unchecked): Control change messages will neither be
transmitted nor received.
This setting has no effect when you use the internal sequencer to
play back sequence data that was recorded with control change
data; i.e., the control changes previously recorded into the
sequencer will be transmitted via MIDI.
Enable Exclusive [Off, On]
On (checked): System Exclusive data will be transmitted and
received.
Check this if you want to edit the KROSS from a connected
computer, or if you want to allow bi-directional editing.
Off (unchecked): System Exclusive data will not be transmitted.
Normally you will leave this unchecked.
However, System Exclusive data will be transmitted and received
while the functions (Dump Program– Dump Drum Track
Pattern) of this page are displayed.
V
1–1...3: FUNCTION
•0: Write Global Setting see page 176
•1: Dump Program see page 178
•2: Dump Combination see page 178
•3: Dump Favorite see page 178
•4: Dump Drum Kit see page 178
•5: Dump Arpeggio Pattern see page 178
•6: Dump Global Setting see page 178
•7: Dump Sequence see page 178
•8: Dump All see page 178
For more information, please see the “Global, Media:
FUNCTION” section on page 176.
To Next Page
Loading...
Need help?
General
