Global/Media mode
162
1–2: OUT
SEQ Mode
Track MIDI Out [for Master, for External Sequencer]
This setting specifies what will be transmitted via MIDI when you
switch songs in Sequencer mode.
for Master: Normally in Sequencer mode, the internal sequencer
can record or play back a performance on the KROSS’s keyboard.
In this case, tracks that are set to EXT or BTH will control external
MIDI sound modules. You can create settings in a song so that
when you select that song on the KROSS, tracks that are set to
EXT or BTH will transmit program changes or other MIDI
messages* to set up your external MIDI sound modules.
for External Sequencer: Choose this setting if you want to use
the KROSS in Sequencer mode as a multi-timbral sound module
driven by an external sequencer. With this setting, even the tracks
that are set to EXT or BTH will not transmit program changes or
other MIDI messages* when you switch songs on the KROSS. In
this case, echo-back from the external MIDI sequencer will not
switch programs or other parameters to the identical settings on
each track that is set to the same MIDI channel.
* Applicable parameters
• Program Select: CC#00 bank select (LSB), CC#32 bank select
(MSB), program change
• Pan: CC#10 pan
• Volume: CC#7 volume
• Portamento: CC#65 portamento On/Off, CC#5 portamento time
• Send 1/2: CC#93 send 1 level, CC#91 send 2 level
• (Post FX) Pan: CC#8 post insert effect pan
Param. MIDI Out [Control Change, SysEx-Param Change]
This setting specifies whether control changes or System
Exclusive messages will be transmitted when you edit a parameter
in Sequencer mode.
Control Change: Data for the edited parameter will be
transmitted as a control change.
SysEx-Param Change: Data for the edited parameter will be
transmitted as a parameter change.
Note: For these to function, Enable Control Change or Enable
Exclusive (G–MIDI> FILTER) must be checked respectively.
* Applicable parameters
• Pan: CC#10 pan
• Volume: CC#7 volume
• Send 1/2: CC#93 send 1 level, CC#91 send 2 level
Drum Track
Drum track programs in Program mode will be triggered on the
global MIDI channel if Trigger Mode is set to Wait KBD Trigger.
The MIDI transmit channel is specified by the Drum Track Prog
MIDI Ch. Use the Drum Track Prog MIDI Out to specify
whether the MIDI note data of the pattern will be transmitted.
Drum track programs do not transmit or receive MIDI program
changes.
Prog MIDI Ch [01…16]
This specifies the MIDI channel for drum track transmission and
reception in Program mode. If Prog MIDI Out is checked, drum
pattern note data will be transmitted on this MIDI channel. The
default setting is channel 10.
Prog MIDI Out [Off, On]
On (checked): The note data of the drum track pattern will be
transmitted on the channel specified by Prog MIDI Ch.
Off (unchecked): The note data of the drum track pattern will not
be transmitted.
Step Seq
The MIDI transmit channel of the step sequencer in Program mode
is specified by the Step Seq Prog MIDI Ch setting. The Step Seq
Prog MIDI Out setting specifies whether MIDI note data of the
pattern will be transmitted.
Drum track programs do not transmit or receive MIDI program
changes.
Prog MIDI Ch [01…16]
This specifies the MIDI channel for step sequencer transmission
and reception in Program mode. If Prog MIDI Out is checked,
drum pattern note data will be transmitted on this MIDI channel.
The default setting is channel 16.
Prog MIDI Out [Off, On]
On (checked): The note data of the step sequencer pattern will be
transmitted on the channel specified by Prog MIDI Ch.
Off (unchecked): The note data of the sequencer pattern will not
be transmitted.
Pad Sampler
The MIDI transmit channel of the Pad Sampler function in
Program mode is specified by Pad Sampler Prog MIDI Ch. Pad
Sampler Prog MIDI Out specifies whether MIDI note data is
transmitted when you play the pads.
Prog MIDI Ch [01…16]
This specifies the MIDI transmit/receive channel of the Pad
Sampler function in Program mode. If Prog MIDI Out is checked,
note data for the pattern is transmitted on this MIDI channel. The
default setting is channel 15.
Prog MIDI Out [Off, On]
On (checked): When you play the pads, note data is transmitted
on the channel specified by Prog MIDI Ch.
Off (unchecked): Note data is not transmitted when you play the
pads. The default setting is Off.
To Next Page
Loading...
Need help?
General
