Korg KROSS - Single Size Effects

Single size effects 000: No Effect
217
Single size effects
About the names of parameters listed in the effect
parameter tables
Two parameter names are listed in these tables.
The parameter name shown at left is the name that's shown in the
display of the KROSS. The parameter name shown at right is the
full name of the parameter. If a “←” is shown, the name shown in
the display of the KROSS is the full parameter name.
Explanations of the parameter will use the full name.
000: No Effect
Select this option when you do not use any effects. The Insert
Effect section outputs unprocessed signals and the Master Effect
section mutes the output.
001: Stereo Compressor
This effect compresses the input signal to regulate the level and
give a “punchy” effect. It is useful for guitar, piano, and drum
sounds. This is a stereo compressor. You can link left and right
channels, or use each channel separately.
Envelope
This parameter selects whether the left and right channels are
linked to control both signals simultaneously, or whether each
channel is controlled independently.
Sensitivity
Output Level
The “Sensitivity” parameter sets the sensitivity of the compressor.
If this parameter is set to a higher value, lower level sounds will be
boosted. With a higher Sensitivity, the overall volume level is
higher. To adjust the final volume level, use the “Output Level”
parameter.
Attack
This parameter controls the attack level.
002: Red Comp
When playing chords on an electric piano or similar instrument,
it’s helpful to use a compressor to keep each note smooth and well-
balanced. In addition to a distinctive percussive accent, it will also
provide a long sustain. This effect models a popular compressor
with a clean sound that’s perfect for pop and funk music.
Paramter Value Explanation
Env Sel
Envelope
Select
L/R Mix,
L/R Individ-
ually
Determines whether
the left and right
channels are linked or
used separately p.217
Sens Sensitivity 1...100
Sets the sensitivity
p.217
Attack ← 1...100
Sets the attack level
p.218
PreEQ Trim ← 0...100
Sets the EQ input
level
Pre LEQ Fc
Low EQ
Frequency
Low,
Mid-Low
Selects the cutoff
frequency (low or
mid-low) of the low-
range equalizer
Pre HEQ Fc
High EQ
Frequency
High,
Mid-High
Selects the cutoff
frequency (high or
mid-high) of the
high-range equalizer
LEQ [dB]
Low EQ
Gain [dB]
–15.0...+15.0
Sets the gain of the
Low EQ
HEQ [dB]
High EQ
Gain [dB]
–15.0...+15.0
Sets the gain of the
High EQ
Out Level ← 0...100
Sets the output level
of the compressor
p.229
Src Source Off...Tempo
Selects the
modulation source
for the compressor
output level
Amt Amount –100...+100
Sets the modulation
amount for the
compressor output
level
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
EQ Trim
EQ Trim
LEQ HEQ
LEQ
HEQ
Compressor
Compressor
Envelope Select
Output Level
Output Level
Envelope - Control
Envelope - Control
Paramter Value Explanation
Sens Sensitivity 1...100 Sets the sensitivity
Attack ← 1...100 Sets the attack level
Level ← 0...100
Sets the output level
of the compressor
Wet/Dry Wet/Dry
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects the
modulation source
for the compressor
output level
Amt Amount –100...+100
Sets the modulation
amount for the
compressor output
level
Sensitivity=100
Sensitivity=40
Dry
Wet
Time
Level
Compressor - Sensitivity
Louder
Dry
Wet
Time
Level
Attack=80
Attack=20
Compressor - Attack
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Right
Wet / Dry
Wet / Dry
+
Envelope - Control
Output Level
Compressor