Single size effects 004: Multiband Limiter
219
Trigger Monitor
Turning this parameter On will cause the trigger signal to be
output, instead of the effect sound. Use this parameter to check the
trigger signal with EQ applied.
Usually, this should be set to Off.
Side PEQ Insert
Side PEQ Cutoff [Hz]
Q
Gain [dB]
These parameters are used to set the EQ amount that’s applied to
the trigger signal.
The Limiter determines whether the compression is applied or not,
based on the post-EQ trigger signal. Setting the equalizer allows
you to set the Limiter to respond to any frequency band.
004: Multiband Limiter
This effect applies the Limiter to the low range, mid range, and
high range of the input signal. You can control dynamics for each
range to adjust the sound pressure of the low range, mid range, and
high range in a different way from the EQ.
Low Offset [dB]
Mid Offset [dB]
High Offset [dB]
These parameters set the gain of the trigger signal.
For example, if you do not want to apply compression to the high
range, reduce the “High Offset” value down below the
“Threshold” level. In this way, the high range limiter will not
respond, and compression will not be applied.
005: St.
MasteringLimiter (Stereo
Mastering Limiter)
This is a stereo limiter that is optimized for mastering songs.
006: Stereo Gate
This effect mutes the input signal when it falls below a specified
level. You can also invert the on/off status of the gate, or use note-
on/off messages to turn the gate on/off directly.
Paramter Value Explanation
Ratio ←
1.0 : 1...50.0 : 1,
Inf : 1
Sets the signal
compression ratio
p.218
Thrsh[dB]
Threshold
[dB]
–40...0
Sets the level above
which the
compressor is applied
p.218
Attack ← 1...100
Sets the attack time
p.218
Release ← 1...100
Sets the release time
p.218
Lo Ofs[dB]
Low Offset
[dB]
–40...0
Gain of the low-range
trigger signal p.219
M. Ofs[dB]
Mid Offset
[dB]
–40...0
Gain of the mid-range
trigger signal p.219
Hi Ofs[dB]
High Offset
[dB]
–40...0
Gain of the high-
range trigger signal
p.219
Gain [dB]
Gain Adjust
[dB]
–Inf,
–38...+24
Sets the output gain
p.218
Src Source Off...Tempo
Selects the
modulation source
for the output gain
Amt Amount –63...+63
Sets the modulation
amount of the output
gain
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Gain Adjust
Mid Offset
Low Offset
High Offset
Envelope - Control
Envelope - Control
Envelope - Control
Low
Mid
High
Band-Pass Filters
+
Limiter
Limiter
Limiter
Paramter Value Explanation
Thrsh [dB]
Threshold
[dB]
–30.0...0.0
Sets the level above
which the
compressor is applied
p.218
Ceil[dB]
Out Ceiling
[dB]
–30.0...0.0 Sets the output gain
Rel [ms] Release [ms] 0.50...1000.0
Sets the release time
p.218
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Paramter Value Explanation
Env Src
Envelope
Source
Dmod, Input,
FX Control1,
FX Control2
Selects the source to
control the gate:
Dmod control, or use
the input signal or FX
Control Bus 1 or 2 as a
trigger p.218
FXCtrl Trim
Fx Control
Trim
0...100
Sets the trigger input
level from FX Control
Bus 1/2
Env Sel Envelope
L/R Mix,
L Only,
R Only
Selects the control
signal: left and right
linked, left only, or
right only p.218
Src Mid Source Off...Tempo
Selects the source
that will control the
gate when Envelope
Src = Dmod
Polarity ← +, –
Switches the polarity
of gating p.220
Threshold ← 0...100
Sets the level where
gating is applied
p.220
Attack ← 1...100
Sets the attack time
p.220
Release ← 1...100
Sets the release time
p.220
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Limiter
Limiter
Out Ceiling
Out Ceiling
Envelope - Control
+
Left
Right
FX Control BUS 1
FX Control BUS 2
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Envelope Source
Gain Adjust
Gain Adjust
Side PEQ
Envelope - Control
Envelope - Control
Trigger Monitor
+
Envelope Select
Gate
Delay
Gate
Delay
D
-mod
To Next Page
Loading...
