Program mode
60
16–3: Insert FX Setup
Here you can choose the type of each insert effect, 1 through 5, its
on/off status, chaining, and adjust the post-IFX mixer settings.
For insert effects, the direct sound (Dry) is always stereo-in and
out. The input/output configuration of the effect sound (Wet)
depends on the effect type.
For more information, please see “Insert Effects (IFX1–IFX5)” on
page 210.
1 (IFX1)
Effect On/Off [Off, On]
Switches the insert effect on/off.
If this is off, the input will simply be passed to the output. (When
000:No Effect is selected, there’s no difference between On and
Off.)
Each time you select this and press the ENTER button, the insert
effect will turn on or off.
Separately from this setting, you can use MIDI CC #92 (on
the global MIDI Channel (G–MIDI> BASIC)) to turn all
insert effects off. A value of 0 turns them off, and values of
1–127 restore the original setting.
Effect Select [000, S00...S63, D00...D10]
This selects the effect type for insert effect.
IFX5 cannot use double-size effects. If you use a double-size
effect, the next insert effect will be unavailable. For example if
you select a double-size effect for IFX1, you won’t be able to use
IFX2.
IFX Select menu
You can also choose effect no.:Name and press the ENTER button
to access the IFX Select menu, and select an effect from the list.
Use the buttons or the VALUE dial to make a selection, and
then press the ENTER button to confirm it.
Chain [Off, On]
This connects insert effects in series.
If Chain is On, this insert effect will be connected in series with
the insert effect selected by ChainTo.
With the On setting, the upper line of the display shows the insert
effect connection status.
Example: IFX1 ChainTo: IFX2
IFX1 Chain: On
Insert effects 1 and 2 will be connected in series. If Bus Select is
set to IFX1, the oscillator’s output will be sent in series through
IFX1 to IFX2. You can connect up to five insert effects (IFX1–
IFX5) in series. In this case, the Pan: #8 (CC#8), Bus select, Fx
Control Bus, Send1, and Send2 settings following the last insert
effect will be used.
Chain to [2...5]
You can chain up to five insert effects together in series, to create
more complex effects. Set up the chain using this parameter, and
then enable it using the Chain check box.
Effects can also join a chain in the middle. For instance, you can
chain IFX1 to IFX2 through IFX5, and IFX2 to IFX3 through
IFX5 as well. IFX4 does not provide a ChainTo setting. It can be
connected only to IFX5. You can’t connect from IFX5 to another
insert effect.
2 (IFX2)
Effect Select [000, S00...S61, D00...D10]
Effect On/Off [Off, On]
Chain [Off, On]
Chain to [3...5]
See “1 (IFX1):”
3 (IFX3)
Effect Select [000, S00...S61, D00...D09]
Effect On/Off [Off, On]
Chain [Off, On]
Chain to [4, 5]
See “1 (IFX1):”
4 (IFX4)
Effect Select [000, S00...S61, D00...D09]
Effect On/Off [Off, On]
Chain [Off, On]
See “1 (IFX1):”
5 (IFX5)
Effect Select [000, S00...S61]
Effect On/Off [Off, On]
See “1 (IFX1):”
Eect On/O Eect Select Chain Chain to
To Next Page
Loading...
Need help?
General
