Single size effects 088: GrainSftr (Grain Shifter)
265
088: GrainSftr (Grain Shifter)
This effect cuts extremely short samples (“grains”) from the input
signal waveform and plays them repeatedly, giving a mechanical
character to the sound.
Duration
LFO Sample Cycle [Hz]
“Duration” sets the length of the sampled grain, and the “LFO
Sample Cycle” controls how often a new grain is sampled. In
between Sample Cycles, the current grain is repeated continuously.
089: L/C/R Delay
This multitap delay outputs three Tap signals to the left, right, and
center respectively. You can also adjust the left and right spread of
the delay sound.
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Paramter Value Explanation
Duration 0...100
Sets the duration of
the grain p.265
Src Source Off...Tempo
Selects the source
that will modulate
the duration of the
grain
Amt Amount –100...+100
Sets the amount by
which the grain
duration will be
modulated
LFO Sync LFO Sync Src Off...Tempo
Selects the
modulation source
that will reset the LFO
LFO [Hz]
LFO Sample
Cycle [Hz]
0.02...20.00
Sets the frequency
where the grain will
be switched p.265
Src Source Off...Tempo
Selects a modulation
source for LFO speed
Amt Amount
–20.00...
+20.00
Sets the modulation
amount of LFO speed
MIDI Sync
BPM/MIDI
Sync
Off, On
When this is on, the
LFO speed is set by
BPM, Base Note, and
Times, instead of
Frequency p.223
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Base Note ← ...
Selects the type of
notes that specify the
LFO speed p.223
Times ← x1...x32
Sets the number of
notes that specify the
LFO speed p.223
Wet/Dry ←
Dry, 1: 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
+
Left
Right
Sample Cycle
Wet / Dry
Wet / Dry
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
LFO
D
-mod
Trigger
Grain Shifter
Paramter Value Explanation
L Dly[ms]
L Delay
Time [ms]
0...2730
Sets the delay time of
TapL
L Level Level 0...50
Sets the output level
of TapL
C Dly[ms]
C Delay
Time [ms]
0...2730
Sets the delay time of
TapC
C Level Level 0...50
Sets the output level
of TapC
R Dly[ms]
R Delay
Time [ms]
0...2730
Sets the delay time of
TapR
Level Level 0...50
Sets the output level
of TapR
Feedbck C
C Delay
Feedback
–100...+100
Sets the feedback
amount of TapC
Src Source Off...Tempo
Selects the
modulation source of
the TapC feedback
amount
Amt Amount –100...+100
Sets the modulation
amount of the TapC
feedback amount
HiDamp[%]
High Damp
[%]
0...100
Sets the damping
amount in the high
range p.266
LoDamp[%]
Low Damp
[%]
0...100
Sets the damping
amount in the low
range p.266
InLvl Dmod
Input Level
Dmod [%]
–100...+100
Sets the modulation
amount of the input
level p.261
Src Source Off...Tempo
Selects the
modulation source
for the input level
p.261
Spread ← 0...50
Sets the width of the
stereo image of the
effect sound
p.266
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
In
Out
Sample Cycle / Duration
Sample Cycle
Duration
C Delay
R Delay
Left
Right
Feedback
Spread
Wet / Dry
Wet / Dry
Wet: Mono In - Stereo Out / Dry: Stereo In - Stereo Out
Input Level D-mod
High Damp
Low Damp
L Delay
Input Level D-mod
+
Level
Level
Level
To Next Page
Loading...
Need help?
General
