Effect Guide
236
Mix
Wet/Dry
The Mix parameter specifies the amount of effect sound relative to
the direct sound. A setting of 0 produces the direct sound, a setting
of about 50 produces chorus, and a setting of 100 produces a
vibrato effect. If you set the Wet/Dry parameter to Wet, the sound
will be output with the mix balance specified by Mix.
034: St. Random Phaser (Stereo
Random Phaser)
This is a stereo phaser. The effect uses a step-shape waveform and
random LFO for modulation, creating a unique phasing effect.
035: St. Env Phaser (Stereo
Envelope Phaser)
This stereo phaser uses an envelope generator for modulation. You
will obtain the same pattern of phasing each time you play. You
can also control the Phaser directly using the modulation source.
Paramter Value Explanation
LFO
LFO
Waveform
Step-Tri,
Step-Sin,
Random
Selects the LFO
Waveform p.226
Phase [deg] ← –180...+180
Sets the LFO phase
difference between
the left and right
p.226
LFO [Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO p.223
Src Source Off...Tempo
Selects the
modulation source
commonly used for
LFO speed and step
speed
Amt Amount
–20.00...
+20.00
Sets the modulation
amount of LFO speed
Step [Hz]
Step Freq
[Hz]
0.05...50.00
Sets the LFO step
speed p.226
Amt Amount
–50.00...
+50.00
Sets the modulation
amount of LFO step
speed
MIDI Sync
BPM/MIDI
Sync
Off, On
When this is on, the
LFO speed is set by
BPM, Base Note, and
Times, instead of
Frequency p.223
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the
system tempo; 40–
300 sets the tempo
manually for this
individual effect p.223
Base Note ← ...
Selects the type of
notes that specify the
LFO speed p.223
Times ← x1...x32
Sets the number of
notes that specify the
LFO speed p.223
Step
Step Base
Note
...
Selects the type of
notes to specify the
LFO step speed p.223
Times ← x1...x32
Sets the number of
notes to specify the
LFO step speed p.223
Depth ← 0...100
Sets the depth of LFO
modulation
Resonance ← –100...+100
Sets the resonance
amount p.235
HiDamp[%]
High Damp
[%
]
0...100
Sets the resonance
damping amount in
the high range p.235
Manual ← 0...100
Sets the frequency
where the effect is
applied
LFO: Step-Tri/Random
Left
Right
Resonance
LFO Phase
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
Phaser
Phaser
Src Source Off...Tempo
Selects the
modulation source
for the LFO
modulation
Amt Amount –100...+100
Sets the modulation
amount of the LFO
modulation
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dry input
p.226, p.235
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Paramter Value Explanation
L ManuBtm
L Manual
Bottom
0...100
Sets the lower limit of
the frequency range
for the effect on the
left channel
L ManuTop
L Manual
Top
0...100
Sets the upper limit of
the frequency range
for the effect on the
left channel
R Man Btm
R Manual
Bottom
0...100
Sets the lower limit of
the frequency range
for the effect on the
right channel
R ManuTop
R Manual
Top
0...100
Sets the upper limit of
the frequency range
for the effect on the
right channel
Sweep Sweep Mode EG, Dmod
Determines whether
the flanger is
controlled by the
envelope generator
or by the modulation
source p.258
Src Source Off...Tempo
Selects the modulation
source that triggers the
EG (when EG is selected
for Sweep Mode), or
modulation source that
causes the flanger to
sweep (when Dmod is
selected for Sweep
Mode) p.258
EG Attack ← 1...100
Sets the EG attack
speed p.258
EG Decay ← 1...100
Sets the EG decay
speed p.258
Resonance ← –100...+100
Sets the resonance
amount p.235
HiDamp[%]
High Damp
[%]
0...100
Sets the resonance
damping amount in
the high range
p.235
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dry input
p.226, p.235
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
EG Attack/Decay
EG
D-mod
Sweep Mode
D
-mod
Phaser
Phaser
Left
Right
Resonance
Wet / Dry
Wet / Dry
High Damp
Stereo In - Stereo Out
To Next Page
Loading...
