Effect Guide
226
Phase [deg]
Offsetting the left and right phases alters how modulation is
applied to the left and right channels, creating a swelling effect.
LFO Waveform
LFO Freq [Hz]
Step Freq [Hz]
When “LFO Waveform” is set to StpTri (Step-Tri), LFO is a step-
shape, Tri (Triangle) waveform. The “LFO Freq [Hz]” parameter
sets the original triangle waveform speed. Changing the “Step
Freq [Hz]” parameter enables you to adjust the width of the steps.
When “LFO Waveform” is set to Rndm (Random), the “Step Freq
[Hz]” parameter uses a random LFO cycle.
BPM
Step Base Note
Times
The width of an LFO step, or a cycle of random LFO, is obtained
by multiplying the length of a note (…) (selected for “Step Base
Note,” in relation to the tempo specified in “BPM,” or the MIDI
Clock tempo if “BPM” is set to MIDI) by the number specified in
the “Times” parameter.
Wet/Dry
The effect sound’s phase will be reversed when you set this
parameter in the range of values from –Wet to –1:99.
015: St.MultiModeFltr (Stereo
Multi Mode Filter)
This is a multi-mode filter with four types; low pass, high pass,
band pass, and band reject. You can use LFO or dynamic
modulation to vary the cutoff frequency or resonance.
Wet/Dry ←
–Wet...
–99 : 1, Dry,
99 : 1...Wet
Sets the balance
between the effect
and the dry input
p.226
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
0+90
+180 [degree]
0 [degree]
–90
–180
LFO Phase
Step Frequency
LFO Frequency
Step Frequency
Step-Tri
Random
Random Filter LFO
Paramter Value Explanation
Filter Type ←
LPF, HPF, BPF,
BRF
Selects the type of
filter
Trim ← 0...100 Sets the input level
Cutoff ← 0...100
Sets the cutoff frequency
(center frequency)
Src Source Off...Tempo
Selects the
modulation source of
the cutoff
Amt Amount –100...+100
Sets the modulation
amount of the cutoff
Resonance ← 0...100
Sets the resonance
amount
Src Source Off...Tempo
Selects the source that
will modulate the
amount of resonance
Amt Amount –100...+100
Sets the amount by
which the resonance
will be modulated
Depth LFO Depth 0...100
Sets the depth of how
the LFO will modulate
the cutoff frequency
LFO
LFO
Waveform
Tri (Triangle),
Sine
Selects the LFO
Waveform
LFO Phase
[deg]
← –180...+180
Sets the LFO phase
difference between the
left and right p.226
LFO [Hz]
LFO Freq
[Hz]
0.02...20.00
Sets the speed of the
LFO p.226
Src Source Off...Tempo
Selects a modulation
source for LFO speed
Amt Amount
–20.00...
+20.00
Sets the modulation
amount of LFO speed
MIDI Sync
BPM/MIDI
Sync
Off, On
When this is on, the LFO
speed is set by BPM, Base
Note, and Times, instead
of Frequency p.223
BPM ←
MIDI,
40.00...
300.00
MIDI syncs to the system
tempo; 40–300 sets the
tempo manually for this
individual effect
p.223
Base Note ← ...
Selects the type of
notes that specify the
LFO speed p.223
Times ← x1...x32
Sets the number of
notes that specify the
LFO speed p.223
Drive Sw ← Off, On
Switches distortion
on/off within the filter
DriveLevel ← 0...100 Sets the output level
Drive Gain ← 0...100
Sets the distortion
amount
Low Boost ← 0...100
Sets the amount of
low-range boost
Wet/Dry ←
Dry, 1 : 99...
99 : 1, Wet
Sets the balance
between the effect
and the dry input
Src Source Off...Tempo
Selects a modulation
source for Wet/Dry
Amt Amount –100...+100
Sets the modulation
amount for Wet/Dry
Left
Right
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
Multimode Filter Driver
Driver
Trim Output
OutputTrim
LFO Phase
LFO: Tri / Sine
LFO Shape
LPF
HPF
BPF
BRF
Filter Type
Multimode Filter
To Next Page
Loading...
