Table of Contents
7
8.10.3 Move manually to tying position .............................................................................................. 150
8.10.4 Activating the wrapping table manually (only for Comprima CV150XC) ................................ 150
8.10.5 Drive lifter manually upward/ downward (Comprima CF155XC/CV210XC) ........................... 151
8.10.6 Opening/closing the bale chamber ......................................................................................... 151
8.10.7 Move swivel table by hand ...................................................................................................... 152
8.11 Menu 3-2 Manual operation wrapper ............................................................................................. 152
8.11.1 Opening/closing the holding arms ........................................................................................... 153
8.11.2 Switching on/off wrapping arm ................................................................................................ 154
8.11.3 Move the wrapping arm to zero position ................................................................................. 154
8.12 Menu 3-2 „Manual Operation Wrapping Arm" CV 210 ................................................................... 155
8.12.1 Move the Height of the Wrapping Arms .................................................................................. 156
8.12.2 Drive Height Wrapping Arm Into Parking Position .................................................................. 157
8.12.3 Error messages Manual operation .......................................................................................... 159
8.13 Main menu 4 Service ..................................................................................................................... 160
8.13.1 Menu 4-2 Manual sensor test ................................................................................................. 161
8.13.2 Actuator test ............................................................................................................................ 171
8.13.3 Menu 4-4 Manual actuator test ............................................................................................... 171
8.13.4 Menu 4-8 Diagnostics ............................................................................................................. 176
8.13.5 Menu 4-9 Manual operation without confirmation prompt....................................................... 177
8.14 Main Menu 5 Information ............................................................................................................... 179
8.15 Main Menu 6 Technician ................................................................................................................ 179
8.16 Main Menu 7 ISOBUS .................................................................................................................... 180
8.16.1 Menu 7-1 Virtual Terminal (VT) ............................................................................................... 181
8.16.2 Menu 7-1-1 Select day/night display lighting .......................................................................... 182
8.16.3 Menu 7-1-3 „Softkeys ISO Terminal“ ...................................................................................... 183
8.16.4 Menu 7-1-4 Switch to different terminal .................................................................................. 185
8.17 Menu 7-4 ISOBUS Diagnostics ...................................................................................................... 186
8.17.1 Menu 7-4-2 Diagnostics Auxiliary Functions (AUX) ................................................................ 187
8.18 Messages ....................................................................................................................................... 188
8.18.1 Query message for bale chamber ........................................................................................... 188
8.18.2 Query message manual operation ......................................................................................... 188
8.18.3 Prompt message Repeat wrapping ......................................................................................... 189
8.18.4 Alarm messages ..................................................................................................................... 190
8.18.5 Acoustic warnings ................................................................................................................... 190
8.18.6 Note and messages ................................................................................................................ 191
8.18.7 Prompts ................................................................................................................................... 193
8.18.8 Physical messages ................................................................................................................. 194
8.18.9 General Messages .................................................................................................................. 196
9 ISOBUS operation .............................................................................................................................. 197
9.1 Mounting ISOBUS Terminal ........................................................................................................... 198
9.1.1 Connection Terminal to Tractor .............................................................................................. 198
9.1.2 Connection Tractor to Machine ............................................................................................... 198
9.2 Differing functions to KRONE ISOBUS terminal CCI ..................................................................... 199
9.3 ISOBUS „Auxiliary“-function (AUX) ................................................................................................ 200
9.3.1 Example of joystick assignment for Fendt (default setting) .................................................... 201
9.3.2 Recommended settings for a WTK multi-function lever (default setting) ................................ 202
10 Operation of the Hydraulic Zero Setting of Blades (Optional) ....................................................... 203
10.1 KRONE ISOBUS Terminal ............................................................................................................. 204
10.1.1 Basic screen in case of a connected zero setting of blades (option) ...................................... 204
To Next Page
Loading...
Need help?
General
