Schweitzer Engineering Laboratories SEL-421-4 - Page 1156

12.14
SEL-400 Series Relays Instruction Manual Date Code 20171006
Settings
Port Settings
Table 12.21 PMU Protocol Settings
Label Prompt Default Value
PMUMODE PMU Mode (CLIENTA, CLIENTB, SERVER) SERVER
RTCID
a
a
Setting hidden when PMUMODE := SERVER.
Remote PMU Hardware ID (1–65534) 1
PMODC PMU Output Data Configuration (1–5) 1
Table 12.22 Simple Network Time Protocol (SNTP) Selection
Setting Prompt Default
ESNTP SNTP Enable (OFF, UNICAST, MANYCAST, BROADCAST) OFF
SNTPRAT
a
a
This setting is hidden if ESNTP = OFF, and hidden and forced to 5 if ESNTP = BROADCAST.
SNTP Request Update Rate (15–3600 seconds) 60
SNTPTO SNTP Timeout (5–20 seconds) 5
SNTPPIP SNTP Primary Server IP Address (w.x.y.z)
b
b
Where w: 0–126, 128–239, x: 0–255, y: 0–255, z: 0–255.
192.168.1.110
SNTPBIP SNTP Backup Server IP Address (w.x.y.z)
c
c
Where w: 0–126, 128–223, x: 0–255, y: 0–255, z: 0–255.
192.168.1.111
SNTPPOR
d
d
This setting is hidden if ESNTP  UNICAST.
SNTP IP Local Port Number (1–65534) 123
Ta b l e 1 2 .23 PTP S e tti n g s
Setting Prompt Default
EPTP Enable PTP (Y, N)
a
a
This setting is not available if the hardware does not support Ports 5A and 5B or if the ports are
used in SWITCHED mode.
N
PTPPRO PTP Profile (DEFAULT, C37.238)
b
b
Hidden and forced to C37.238 if Port 5A or 5B is used for the process bus (87L or IEC 61850-9-2
Sampled Values).
DEFAULT
PTPTR PTP Transport Mechanism (UDP, LAYER2)
c
c
Hide if PTPPRO = C37.238.
UDP
DOMNUM PTP Domain Number (0–255) 0
PTHDLY PTP Path Delay Mechanism (P2P, E2E, OFF)
d
d
If PTPPRO = C37.238, E2E is removed from the setting range.
E2E
PDINT Peer Delay Request Interval (1, 2, 4, ...64 s)
e
e
Hide if PTHDLY = E2E or OFF.
1
AMNUM PTP Number of Acceptable Masters (OFF, 1–5) OFF
AMIPn PTP Acceptable Master n IP (w.x.y.z)
f
f
Hide if AMNUM = OFF or if PTPTR = LAYER2.
192.168.1.12n
AMMACn PTP Acceptable Master n MAC (xx:xx:xx:xx:xx:xx)
g
g
Hide if AMNUM = OFF or if PTPTR = UDP.
00.30.A7:00:00:0[p]
ALTPRIn PTP Alternate Priority1 for Master n (0–255)
h
h
Hide if AMNUM = OFF.
0
PVLAN PTP VLAN Identifier (0–4094)
i
i
Hide if PTPPRO = DEFAULT.
0
PVLANPR PTP VLAN Priority (0–7)
i
4
NOTE: PTP is only supported on
Ethernet Ports 5A and 5B. Most SEL-400
series relays only support 2 ports at a
time, and must have Port 5A and Port 5B
selected by the MOT option in these
relays. Relays that support 4 ports will
still have PTP on Port 5A and Port 5B but
will not require selection of a different
MOT option to have PTP available.