Emotron VS10 - Page 311

Parameter
Name / value range / [default setting]
Info
0x4045:019
(P754.19)
Parameter value set 4: Value of parameter 19
(Par. value set 4: Set 4 Value 19)
-2147483648 ... [0] ... 2147483647
0x4045:020
(P754.20)
Parameter value set 4: Value of parameter 20
(Par. value set 4: Set 4 Value 20)
-2147483648 ... [0] ... 2147483647
0x4045:021
(P754.21)
Parameter value set 4: Value of parameter 21
(Par. value set 4: Set 4 Value 21)
-2147483648 ... [0] ... 2147483647
0x4045:022
(P754.22)
Parameter value set 4: Value of parameter 22
(Par. value set 4: Set 4 Value 22)
-2147483648 ... [0] ... 2147483647
0x4045:023
(P754.23)
Parameter value set 4: Value of parameter 23
(Par. value set 4: Set 4 Value 23)
-2147483648 ... [0] ... 2147483647
0x4045:024
(P754.24)
Parameter value set 4: Value of parameter 24
(Par. value set 4: Set 4 Value 24)
-2147483648 ... [0] ... 2147483647
0x4045:025
(P754.25)
Parameter value set 4: Value of parameter 25
(Par. value set 4: Set 4 Value 25)
-2147483648 ... [0] ... 2147483647
0x4045:026
(P754.26)
Parameter value set 4: Value of parameter 26
(Par. value set 4: Set 4 Value 26)
-2147483648 ... [0] ... 2147483647
0x4045:027
(P754.27)
Parameter value set 4: Value of parameter 27
(Par. value set 4: Set 4 Value 27)
-2147483648 ... [0] ... 2147483647
0x4045:028
(P754.28)
Parameter value set 4: Value of parameter 28
(Par. value set 4: Set 4 Value 28)
-2147483648 ... [0] ... 2147483647
0x4045:029
(P754.29)
Parameter value set 4: Value of parameter 29
(Par. value set 4: Set 4 Value 29)
-2147483648 ... [0] ... 2147483647
0x4045:030
(P754.30)
Parameter value set 4: Value of parameter 30
(Par. value set 4: Set 4 Value 30)
-2147483648 ... [0] ... 2147483647
0x4045:031
(P754.31)
Parameter value set 4: Value of parameter 31
(Par. value set 4: Set 4 Value 31)
-2147483648 ... [0] ... 2147483647
0x4045:032
(P754.32)
Parameter value set 4: Value of parameter 32
(Par. value set 4: Set 4 Value 32)
-2147483648 ... [0] ... 2147483647
0x4046
(P755.00)
Activation of parameter set
(PSet activation)
Selection of the activation method for the parameter change-over.
If the selection is changed from "Via command... [0]/[1]" to "If the
selection is changed...[2]/[3]" after switch-on, the parameter set
selected via the functions "Select parameter set (bit 0)" and "Select
parameter set (bit 1)" is activated immediately. In case of selection
[2], however, this only takes place if the inverter is disabled, the motor
is stopped or an error is active.
0
Via command (disable required)
The parameter set selected via the functions "Select parameter set (bit
0)" and "Select parameter set (bit 1)" is activated if the trigger assigned
to the "Load parameter set" function in
0x2631:040 (P400.40) provides a
FALSE-TRUE edge AND the inverter is inhibited, the motor is stopped or
an error is active.
1 Via command (immediately) The parameter set selected via the functions "Select parameter set (bit
0)" and "Select parameter set (bit 1)" is immediately activated if the
trigger assigned to the "Load parameter set" function in 0x2631:040
(P400.40) provides a FALSE-TRUE edge.
2
If the selection is changed (disable required)
The parameter set selected via the functions "Select parameter set (bit
0)" and "Select parameter set (bit 1)" is activated if the state of these
selection bits changes AND the inverter is inhibited, the motor is
stopped or an error is active.
3
If the selection is changed (immediately)
The parameter set selected via the functions "Select parameter set (bit
0)" and "Select parameter set (bit 1)" is activated immediately if the
state of these selection bits is changed.