Emotron VS10 - Setpoint Source of Preset Setpoints

404 01-6203-01R3, CG Drives & Automation
0
Not connected
No trigger assigned (trigger is constantly FALSE).
116
Network setpoint active
(from version 02.00)
TRUE if a change-over to network setpoint is requested via bit 6 of the
AC drive control word0x400B:001 (P592.01). Otherwise FALSE.
Notes:
Set this selection if the network setpoint is to be activated via bit 6 of
the AC drive control word.
The AC drive control word can be used with any communication
pro
tocol.
 AC Drive Profile

188
12.3.5. Setpoint source of preset setpoints
The four functions "Activate preset (bit 0)" ... " Activate preset (bit 3)" enable change-over
of the setpoint to a parameterisable setpoint (preset value).
Preconditions
A setpoint change-over to the respective preset is only effected if no setpoint source with
a higher priority has been selected.
 Priority of the setpoint sources  380
Details
A preset is selected in a binary-coded fashion via the triggers assigned to the four
functions "Activate preset (bit 0)" ... " Activate preset (bit 3)" in compliance with the
following truth table:
Activate preset
Selection
Bit 3
0x2631:021
(P400.21)
Bit 2
0x2631:020
(P400.20)
Bit 1
0x2631:019
(P400.19)
Bit 0
0x2631:018
(P400.18)
Preset
Frequency setpoint
PID setpoint
Torque setpoint
FALSE
FALSE
FALSE
FALSE
No preset selected
FALSE
FALSE
FALSE
TRUE
Preset 1
0x2911:001 (P450.01)
0x4022:001 (P451.01)
0x2912:001 (P452.01)
FALSE
FALSE
TRUE
FALSE
Preset 2
0x2911:002 (P450.02)
0x4022:002 (P451.02)
0x2912:002 (P452.02)
FALSE
FALSE
TRUE
TRUE
Preset 3
0x2911:003 (P450.03)
0x4022:003 (P451.03)
0x2912:003 (P452.03)
FALSE
TRUE
FALSE
FALSE
Preset 4
0x2911:004 (P450.04)
0x4022:004 (P451.04)
0x2912:004 (P452.04)
FALSE
TRUE
FALSE
TRUE
Preset 5
0x2911:005 (P450.05)
0x4022:005 (P451.05)
0x2912:005 (P452.05)
FALSE
TRUE
TRUE
FALSE
Preset 6
0x2911:006 (P450.06)
0x4022:006 (P451.06)
0x2912:006 (P452.06)
FALSE
TRUE
TRUE
TRUE
Preset 7
0x2911:007 (P450.07)
0x4022:007 (P451.07)
0x2912:007 (P452.07)
TRUE
FALSE
FALSE
FALSE
Preset 8
0x2911:008 (P450.08)
0x4022:008 (P451.08)
0x2912:008 (P452.08)
TRUE
FALSE
FALSE
TRUE
Preset 9
0x2911:009 (P450.09)
...
...
...
TRUE
TRUE
TRUE
TRUE
Preset 15
0x2911:015 (P450.15)
Notes:
• The frequency setpoint preset 5 is also used for the "Jog foward (CW)" 0x2631:010
(P400.10) function.
• The frequency setpoint preset 6 is also used for the "Jog reverse (CCW)" 0x2631:011
(P400.11) function.