TX150 S8 / TX200 S7
Upgrade and Maintenance Manual
5.1.4 Verifying and configuring the backup software solution . . . . . 83
5.1.5 Note on server maintenance in a Multipath I/O environment . . 83
5.1.6 Switching on the ID indicator . . . . . . . . . . . . . . . . . . 86
5.2 Completing the maintenance task . . . . . . . . . . . . . . . 87
5.2.1 Updating or recovering the system board BIOS and iRMC . . . 87
5.2.1.1 Updating or recovering the system board BIOS . . . . . . . 87
5.2.1.2 Updating or recovering the iRMC . . . . . . . . . . . . . . 87
5.2.2 Verifying system information backup / restore . . . . . . . . . . 89
5.2.3 Updating RAID controller firmware . . . . . . . . . . . . . . . 90
5.2.4 Enabling Option ROM scan . . . . . . . . . . . . . . . . . . . 91
5.2.5 Verifying and configuring the backup software solution . . . . . 92
5.2.6 Resetting the boot retry counter . . . . . . . . . . . . . . . . . 93
5.2.6.1 Viewing the boot retry counter . . . . . . . . . . . . . . . . 93
5.2.6.2 Resetting the boot retry counter . . . . . . . . . . . . . . . 93
5.2.7 Enabling SVOM boot watchdog functionality . . . . . . . . . . 94
5.2.8 Enabling replaced components in the system BIOS . . . . . . . 95
5.2.9 Verifying the memory mode . . . . . . . . . . . . . . . . . . . 96
5.2.10 Verifying the system time settings . . . . . . . . . . . . . . . . 96
5.2.11 Viewing and clearing the System Event Log (SEL) . . . . . . . 97
5.2.11.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . 97
5.2.11.2 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . . 98
5.2.12 Updating the NIC configuration file in a Linux environment . . . 99
5.2.13 Enabling BitLocker functionality . . . . . . . . . . . . . . . . . 100
5.2.14 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 101
5.2.15 Looking up changed MAC / WWN addresses . . . . . . . . . . 101
5.2.15.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . 102
5.2.15.2 Looking up WWN addresses . . . . . . . . . . . . . . . . . 102
5.2.16 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 103
5.2.17 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . 104
5.2.17.1 After replacing / upgrading LAN controllers . . . . . . . . . 104
5.2.17.2 After replacing the system board . . . . . . . . . . . . . . . 104
5.2.18 Switching off the ID indicator . . . . . . . . . . . . . . . . . . 105
5.2.19 Specifying the chassis model . . . . . . . . . . . . . . . . . . 105
5.2.20 Performing a fan test after replacing a defective fan . . . . . . 106
6 Power supply units . . . . . . . . . . . . . . . . . . . . . . . 109
6.1 Basic information . . . . . . . . . . . . . . . . . . . . . . . 110
6.1.1 Power supply unit configurations . . . . . . . . . . . . . . . . 110
6.1.2 Assembly rules . . . . . . . . . . . . . . . . . . . . . . . . . 111
To Next Page
Loading...
Need help?
General