Rohde & Schwarz R&S SMW200A - Page 1144

Remote Control Commands
R&S
®
SMW200A
1144User Manual 1175.6632.02 ─ 30
Suffix Value range Description
BBMM<ch>
1 to 2 DIG I/Q connector
Option: R&S SMW-B9/-K19:
HS DIG I/Q connector
See also Chapter 4.3.4, "Supported Digital Interfaces
Depending on the System Configuration", on page 119.
FADer<ch>
1 to 4
*)
Option: R&S SMW-B10
DIG I/Q connector
*)
The number of the available DIG I/Q connectors on the
FADER boards depends on the selected configuration
(see also :SCONfiguration:FADing).
CHANnel<ch0>
0 to 7 Option: R&S SMW-B9/-K19
Channel number
Up to 8 channels per HS DIG I/Q interface and max. 8
channels for both interfaces.
Example: Enabling and configuring the HS DIG I/Q digital outputs
Option: R&S SMW-B9/-K19
SCONfiguration:MODE ADV
SCONfiguration:OUTPut:MODE HSD
SCONfiguration:FADing SISO4X1X1
SCONfiguration:BASeband:SOURce SEP
SCONfiguration:DIQ:BBMM1:CHANnels CH4
SCONfiguration:DIQ:BBMM2:CHANnels CH2
SCONfiguration:APPLy
SCONfiguration:OUTPut:MAPPing:BBMM1:CHANnel0:MODE ADD
SCONfiguration:OUTPut:MAPPing:BBMM1:CHANnel0:STReam2:STATe 1
SCONfiguration:OUTPut:MAPPing:BBMM1:CHANnel1:STReam2:STATe 0
SCONfiguration:OUTPut:MAPPing:BBMM1:CHANnel1:STReam2:STATe 1
SCONfiguration:OUTPut:MAPPing:BBMM1:CHANnel1:STReam2:STATe 0
SCONfiguration:OUTPut:MAPPing:BBMM2:CHANnel0:MODE ADD
SCONfiguration:OUTPut:MAPPing:BBMM1:CHANnel1:STReam2:STATe 1
SCONfiguration:OUTPut:MAPPing:BBMM2:CHANnel0:STReam1:STATe 1
SCONfiguration:OUTPut:MAPPing:BBMM2:CHANnel0:STReam2:STATe 1
SCONfiguration:OUTPut:MAPPing:BBMM2:CHANnel0:STReam3:STATe 1
SCONfiguration:OUTPut:MAPPing:BBMM2:CHANnel0:STReam4:STATe 1
SCONfiguration:OUTPut:MAPPing:BBMM2:CHANnel1:STReam4:STATe 1
SOURce1:IQ:OUTPut:DIGital:BBMM1:STATe 1
SOURce1:IQ:OUTPut:DIGital:BBMM1:COMMon:STATe 1
SOURce1:IQ:OUTPut:DIGital:BBMM1:SRATe 100000000
SOURce1:IQ:OUTPut:DIGital:BBMM1:CHANnel0:STATe 1
SOURce1:IQ:OUTPut:DIGital:BBMM1:CHANnel0:NAMe "BBMM1_CH0"
SOURce1:IQ:OUTPut:DIGital:BBMM1:CHANnel0:SRATe?
// 100000000
SOURce Subsystem