2JZ/2JX/2JV/2H7
2-3-45
YC8 B11 BELT JAM O 0/3.3 V DC JDS: On/Off
Connected
to the
engine PWB
B12 LOOP SENS O 0/3.3 V DC LS: On/Off
B13 REG UP1 CLT
REM
I 0/24 V DC RCL: On/Off
B14 ROL UP2 CLT
REM
I 0/24 V DC MCL: On/Off
B15 FEED1 JAM O 0/3.3 V DC FSW1: On/Off
B16 MPF2 JAM O 0/3.3 V DC MPPCSW: On/Off
B17 LSU SOL DR I 0/24 V DC LSUCSOL: On/Off
B18 REG JAM O 0/3.3 V DC RSW: On/Off
B19 FED1 CLT REM I 0/24 V DC PFCL1: On/Off
B20 MT_PD I 0/3.3 V DC PCM current control signal
YC9 1 ROL MT PD I 0/3.3 V DC MM current control signal
Connected
to the
engine PWB
2 ROL MT DR I 0/3.3 V DC MM: On/Off
3 ROL MT CLK I 0/3.3 V DC (pulse) MM clock signal
4 REG MT PD I 0/3.3 V DC RM current control signal
5 REG MT DR I 0/3.3 V DC RM: On/Off
6 REG MT CLK I 0/3.3 V DC (pulse) RM clock signal
YC10 1 GND - - Ground
Connected
to the regis-
tration
switcn, MP
paper con-
veying
switch and
feed switch
1
2 REG JAM I 0/3.3 V DC RSW: On/Off
3 +5V1 O 5 V DC 5 V DC power to RSW
4 GND - - Ground
5 MPF2 JAM I 0/3.3 V DC MPPCSW: On/Off
6 +5V1 O 5 V DC 5 V DC power to MPPCSW
7 GND - - Ground
8 FEED1 JAM I 0/3.3 V DC FSW1: On/Off
9 +5V1 O 5 V DC 5 V DC power to FSW1
YC11 1 CAS OPEN I 0/3.3 V DC LC2SW: On/Off
Connected
to the left
cover 2
switch and
feed switch
2
2 GND - - Ground
3 GND - - Ground
4 FEED2 JAM I 0/3.3 V DC FSW2: On/Off
5 +5V1 O 5 V DC 5 V DC power to FSW2
YC12 1 GND - - Ground
Connected
to the feed
switch 3
2 FEED3 JAM I 0/3.3 V DC FSW3: On/Off
3 +5V1 O 5 V DC 5 V DC power to FSW3
YC13 1 +24V2 O 24 V DC 24 V DC power to FCL2
Connected
to the feed
clutch 1/2
(40/40, 50/
40 ppm
model)
2 ROL UP2 CLT
REM
O 0/24 V DC FCL2: On/Off
3 +24V2 O 24 V DC 24 V DC power to FCL1
4 REG UP1 CLT
REM
O 0/24 V DC FCL1: On/Off
Connector Pin No. Signal I/O Voltage Description
To Next Page
Loading...
