Siemens SINUMERIK Series Function Manual

Contents
Extended Functions
22 Function Manual, 03/2013, 6FC5397-1BP40-3BA1
17.4.3 Speed monitoring...................................................................................................................... 827
17.4.4 Selection/deselection of tool monitoring ................................................................................... 828
17.5
Constant grinding wheel peripheral speed (GWPS). ................................................................ 829
17.5.1
General information................................................................................................................... 829
17.5.2
Selection/deselection and programming of GWPS, system variable ....................................... 830
17.5.3
GWPS in all operating modes................................................................................................... 831
17.5.4
Programming example for GWPS............................................................................................. 832
17.6
Supplementary Conditions........................................................................................................ 833
17.6.1
Tool changes with online tool offset.......................................................................................... 833
17.7
Data lists.................................................................................................................................... 834
17.7.1
Machine data............................................................................................................................. 834
17.7.1.1
General machine data............................................................................................................... 834
17.7.1.2
Channelspecific machine data .................................................................................................. 834
17.7.1.3
Axis/spindlespecific machine data ............................................................................................ 834
17.7.2
Signals....................................................................................................................................... 834
17.7.2.1
Signals from axis/spindle .......................................................................................................... 834
18
Z2: NC/PLC interface signals................................................................................................................. 835
18.1
Digital and analog NCK I/Os (A4) ............................................................................................. 835
18.1.1
Signals to NC (DB10)................................................................................................................ 835
18.1.2
Signals from NC (DB10)............................................................................................................ 843
18.2
Distributed systems (B3)........................................................................................................... 846
18.2.1
Defined logical functions/defines .............................................................................................. 846
18.2.2
Interfaces in DB19 for M:N........................................................................................................ 849
18.2.3
Signals from NC (DB10)............................................................................................................ 856
18.2.4
Signals from axis/spindle (DB31, ...)......................................................................................... 857
18.3
Manual and Handwheel Travel (H1) ......................................................................................... 858
18.3.1
Signals from NC (DB10)............................................................................................................ 858
18.3.2
Signals to channel (DB21, ...) ................................................................................................... 861
18.3.3
Signals from channel (DB21, ...) ............................................................................................... 867
18.3.4
Signals with contour handwheel ............................................................................................... 874
18.3.5
Signals to axis/spindle (DB31, ...) ............................................................................................. 876
18.3.6
Signals from axis/spindle (DB31, ...)......................................................................................... 881
18.4
Compensations (K3) ................................................................................................................. 884
18.5
Mode Groups, Channels, Axis Replacement (K5).................................................................... 885
18.5.1
Signals to axis/spindle (DB31, ...) ............................................................................................. 885
18.5.2
Signals from axis/spindle (DB31, ...)......................................................................................... 886
18.6
Kinematic Transformation (M1)................................................................................................. 886
18.6.1
Signals from channel (DB21, ...) ............................................................................................... 886
18.7
Measurement (M5).................................................................................................................... 887
18.7.1
Signals from NC (DB10)............................................................................................................ 887
18.7.2
Signals from axis/spindle (DB31, ...)......................................................................................... 887
18.8
Software cams, position switching signals (N3)........................................................................ 888
18.8.1
Signal overview ......................................................................................................................... 888
18.8.2
Signals from NC (DB10)............................................................................................................ 889
18.8.3
Signals to axis/spindle (DB31, ...) ............................................................................................. 890
18.8.4
Signals from axis/spindle (DB31, ...)......................................................................................... 890

Siemens SINUMERIK Series Specifications

General

Axes Control	Up to 31 axes
Category	Control Unit
Manufacturer	Siemens
Series	SINUMERIK
Control Type	CNC
Communication Interfaces	Ethernet, USB
Operating Temperature	0°C to 45°C
Protection Class	IP20
Power Supply	24V DC
Display	Color TFT LCD