Toa VX-2000SF User Manual

INSTRUCTION MANUAL
INTEGRATED VOICE EVACUATION SYSTEM
VX-2000 series
1134
TOA Electronics Europe GmbH
Suederstrasse 282, 20537 Hamburg, Germany
1134-CPR-110
EN 54-16: 2008
Fire detection and fire alarm systems
— Part 16: Voice alarm control and indicating equipment
Options:
Audible warning of emergency
Manual silencing of the voice alarm condition
Manual reset of the voice alarm condition
Voice alarm condition output to CIE
Indication of faults related to voice alarm zones
Emergency microphone(s)
Voice alarm manual control
Redundant power amplifiers
14
DoP 14-002
Thank you for purchasing TOA's Integrated Voice Evacuation System.
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
When an EN 54-16 compliant VX-2000 system has to be installed, then carefully read the separate manual
titled "APPENDIX: ADDITIONAL INSTALLATION INSTRUCTIONS FOR AN EN 54-16 COMPLIANT
SYSTEM" and follow up the installation and configuration requirements explained therein. This APPENDIX
contains the basic description of settings and installations, so please refer to the general instruction
sections in this document for more details.
Note
Refer to the Instruction Manual attached to the VX-2000DS/3000DS for the installation of the the VX-
2000DS or VX-3000DS Emergency power supply, the VX-2000PF Power supply frame, and the VX-200PS
Power supply unit.
Система оповещения TOA VX-2000 | toa.com.ua

Toa VX-2000SF Specifications

General

Model	VX-2000SF
Control Input	open voltage: 24 V DC, short-circuit current: 2 mA
Operating Temperature	0°C to +40°C
Emergency Microphone Input	balanced, phantom power
Music Input	1 (RCA pin jack, unbalanced)
Microphone Input	balanced, phantom power
Line Input	10 kΩ, balanced
Speaker Output	100 V line
Line Output	600 Ω, balanced

Summary

Chapter 1: NOTE

3. HANDLING PRECAUTIONS

Outlines critical safety and operational guidelines to prevent damage, injury, or malfunction during installation and use.

Chapter 3: SYSTEM OPERATION OUTLINE

4. SPEAKER LINE FAILURE DETECTION METHODS

Explains impedance and pilot tone detection methods for identifying speaker line failures.

Chapter 4: FUNCTIONS

Chapter 5: OPERATION

1. OPERATING THE REMOTE MICROPHONE BY USING A PASSWORD

Explains how to set and enter passwords for remote microphone operation to enhance security.

2. EMERGENCY BROADCASTS

Covers emergency EV messages and remote microphone broadcasts, including dual and single-origin types.

5. FAILURE OUTPUT DETECTION

Explains how to indicate and monitor system failures using remote microphone settings.

Chapter 7: PC SOFTWARE OFFLINE SETTINGS

1. SETUP PROCEDURE (from installation to settings)

3. SOFTWARE INSTALLATION

5. VX-2000 SETTING SOFTWARE ACTIVATION

7. CONFIGURATION SETTING MODE

Details how to configure system settings, including SF module, VX, and RM properties.

8. SYSTEM SETTING MODE

Covers setting broadcast priorities, initial volume, and equalizer parameters in the software.

9. OPERATION SETTING MODE

Explains settings for emergency broadcasts, patterns, and failure output configurations.

10. ACTIVATION SETTING MODE

Covers assigning functions to remote mic keys, control inputs, and internal timer settings.

Chapter 8: INSTALLATION AND SETTING PROCEDURES (HARDWARE)

1. RM-200XF AND RM-200X MICROPHONES

Details the installation and DIP switch settings for RM-200XF and RM-200X microphones.

2. VX-2000, VX-200XR, VX-200XI, AND EV-200

Covers installation procedures for VX-2000, VX-200XR, VX-200XI, and EV-200 modules.

3. VX-2000SF, VX-200SZ , VX-200SP, VX-200SI , VX-200SO, AND VX-200SE

Explains installation and DIP switch settings for VX-2000SF frame modules.

4. VP-2064, VP-2122, VP-2241 AND VP-2421 POWER AMPLIFIERS

Details installation, speaker line voltage changes, and fuse replacement for VP power amplifiers.

5. VP-3154, VP-3304 AND VP-3504 POWER AMPLIFIERS

Covers speaker line voltage changes, ground lifting, BGM sensitivity, and fuse replacement.

6. RACK MOUNTING

Provides precautions and guidelines for mounting equipment in a rack system.

Chapter 9: CONNECTIONS

1. VX-2000 CONNECTIONS TO REMOTE MICROPHONES AND INPUT SOURCE EQUIPMENT

3. SF MODULES (VX-200SP, VX-200SZ, VX-200SI, VX-200SO) CONNECTIONS

4. CONNECTIONS BETWEEN VX-2000SF AND STANDBY AMPLIFIER

6. CONNECTION CABLE PIN ASSIGNMENT

Chapter 10: PC ONLINE CHECKS AND ADJUSTMENTS

1. SYSTEM SETUP PROCEDURE

Provides a flowchart for the system setup process, including PC connections and settings.

2. SYSTEM SETTING FILE DOWNLOAD

Details the process of downloading system setting files from a PC to the VX-2000.

3. SYSTEM CHECK FUNCTIONS

Covers system check functions like configuration, connection, and impedance checks via PC.

4. VOLUME AND EQUALISER SETTINGS

Chapter 11: OTHER PC SOFTWARE FUNCTIONS

1. MONITOR OPERATION CHECK

2. SYSTEM SETTING FILE UPLOAD

3. READING LOGS