ADVANTEST R3765G Series - Page 17

F-2
R3765/67G Series Network Analyzer Operation Manual
List of Illustrations
No. Title Page
5-5 Logarithmic Magnitude/Phase Measurement (Split Display) .............................. 5-7
5-6 Logarithmic Magnitude/Group Delay Measurement (Split Display) .................... 5-8
5-7 Linear Magnitude/Phase Measurement (Split Display) ....................................... 5-9
5-8 Setup of the Reflection Characteristic Measurement .......................................... 5-10
5-9 Calibration of 2-Port Reflection (Test Port/Open) ............................................... 5-11
5-10 Calibration of 2-Port Reflection (Test Port/Short) ............................................... 5-12
5-11 Calibration of 2-Port Reflection (Test Port/Load) ................................................ 5-13
5-12 Execution of 2-Port Reflection Characteristic Calibration ................................... 5-14
5-13 Calibration of 2-Port Transmission Characteristic (Forward Direction) ............... 5-15
5-14 Execution of 2-Port Transmission Characteristic Calibration .............................. 5-16
5-15 Execution of the Isolation Calibration .................................................................. 5-17
5-16 Execution of 2-Port Full Calibration .................................................................... 5-18
5-17 4 Screen Display (Channel 1) ............................................................................. 5-19
5-18 4 Screen Display (Overlap Display of Channel 1 and 3) ..................................... 5-20
5-19 4 Screen Display (Split Display of Channel 1 and 3) .......................................... 5-21
5-20 4 Screen Display (Channel 2) ............................................................................. 5-22
5-21 4 Screen Display (Split Display of Channel 2 and 4) .......................................... 5-23
5-22 The Finished 4 Screen Display ........................................................................... 5-24
5-23 Two Channels Simultaneous Display (Overlap Display) ..................................... 5-26
5-24 Two Channels Simultaneous Display (Split Display) .......................................... 5-27
5-25 Multi-marker Display ........................................................................................... 5-29
5-26 Display of Multi-marker List ................................................................................. 5-30
5-27 Specification of Delta Section (Partial Search) ................................................... 5-32
5-28 Measurement of Maximum Value in the Delta section ........................................ 5-33
5-29 Measurement of Minimum Value in the Delta Section ........................................ 5-34
5-30 Measurement of Ripple in the Delta Section ....................................................... 5-35
5-31 Electrical Length of Cable ................................................................................... 5-37
5-32 Electrical Length Correction Mode ...................................................................... 5-38
5-33 Measurement of Electrical Length ...................................................................... 5-39
5-34 Linear Sweeping ................................................................................................. 5-40
5-35 Setting of Program Sweeping ............................................................................. 5-41
5-36 Execution of the Program Sweep ....................................................................... 5-43
5-37 Change of the Program Sweep ........................................................................... 5-44
5-38 Screen before Execution of Limit Line Measurement ......................................... 5-45
5-39 Setting of the Limit Line ...................................................................................... 5-46
5-40 Limit Line Editing ................................................................................................. 5-47
5-41 Setting of Segment 0 .......................................................................................... 5-48
5-42 Setting of Each Segment .................................................................................... 5-49
5-43 Execution of Limit Test ........................................................................................ 5-50
5-44 Change of Limit Line ........................................................................................... 5-51
6-1 Setting of Plotter GPIB Address .......................................................................... 6-1
6-2 Change of Plotter Initial Setup Value (Initial Value) ............................................ 6-2
6-3 Output Data to the Plotter ................................................................................... 6-3
6-4 Output Result of the Plotter ................................................................................. 6-4
6-5 Saving into the Save-Register ............................................................................ 6-5
6-6 Recalling from the Recall-register ....................................................................... 6-6
6-7 Saving to the Floppy Disk ................................................................................... 6-8