Emotron VS10 - Page 485

Error code
Info
Error type
Adjustable in
dec
hex
Keypad display
Error message
30359 0x7697 Parameter loss Parameter changes lost Fault -
Changed parameter settings got lost due to the removal of the 24-V voltage supply.
In order to reset the error, there are the following options:
Execute device command "Load default settings" 0x2022:001 (P700.01).
Execute device command "Save user data" 0x2022:003 (P700.03).
Switch inverter off and on again without plugged-in USB module.
Notes:
Serious error: The inverter is inhibited immediately. The motor becomes torqueless
(coasts).
33045
0x8115
Time-out (PAM)
Time-out (PAM)
No response
0x2552:004
(P595.04)
The parameter access monitoring has been triggered.
 Parameter access monitoring (PAM)

196
33154
0x8182
CAN bus off
CAN: bus off
Trouble
0x2857:010
A change to the "Bus-Off" state has been made.
33155
0x8183
CAN bus warning
CAN: warning
Warning
0x2857:011
Notes:
When the error type is set to "Warning", only logging takes place (Error history buffer/
Logbook)
33156
0x8184
CAN heartb. C1
CAN: heartbeat time-out consumer 1
Fault
0x2857:005
 CANopen heartbeat protocol  202
33157
0x8185
CAN heartb. C2
CAN: heartbeat time-out consumer 2
Fault
0x2857:006
 CANopen heartbeat protocol  202
33158
0x8186
CAN heartb. C3
CAN: heartbeat time-out consumer 3
Fault
0x2857:007
 CANopen heartbeat protocol  202
33159 0x8187 CAN heartb. C4 CAN: heartbeat time-out consumer 4 Fault 0x2857:008

CANopen heartbeat protocol
 202
33168
0x8190
Watchdog timeout
Network: watchdog timeout
Fault
-
33170 0x8192
Net. Init. error
Network: initialisation error
Fault -
33171 0x8193
Inv. cyclic data
Network: invalid cyclic process data
Trouble -
33184 0x81A0
Modbus TX error Modbus transmit message error
Warning -
Notes:
Logging only (Error history buffer/Logbook)
33185
0x81A1
Modbus time-out
Modbus: network time-out
Fault
0x2858:001
(P515.01)
No valid messages have been received via the Modbus for a longer time than the time-out
time set in 0x2858:002 (P515.02).
33186
0x81A2
Modbus request
Modbus: incorrect request by master
Warning
-
Notes:
Logging only (Error history buffer/Logbook)
33414
0x8286
PDO map error
Network: PDO mapping error
Fault
-
33425
0x8291
Timeout RPDO1
CAN: RPDO1 time-out
Fault
0x2857:001
The RPDO was not received within the monitoring time set for the RPDO or not with the
configured sync.
 CANopen process data objects

204
33426 0x8292 Timeout RPDO2 CAN: RPDO2 time-out Fault 0x2857:002
The RPDO was not received within the monitoring time set for the RPDO or not with the
configured sync.
 CANopen process data objects

204
33427
0x8293
Timeout RPDO3
CAN: RPDO3 time-out
Fault
0x2857:003
The RPDO was not received within the monitoring time set for the RPDO or not with the
configured sync.
 CANopen process data objects

204
33553
0x8311
Torque limit
Torque limit reached
No response
0x2D67:001