MacDon FD75 - Page 11

214323 ix Revision A
3.8.2 Case IH 2300/2500 and 5088/6088/7088 Combines ..................................................................107
Engaging Auto Header Height Control (Case IH 2300) ..............................................................107
Calibrating Auto Header Height Control (AHHC) (Case IH 2300/2500 and 5088/6088/
7088) ........................................................................................................................108
Setting Sensitivity of Auto Header Height Control (Case IH 2300/2500 and
5088/6088/7088)........................................................................................................109
3.8.3 Case IH 5130/6130/7130, 7010/8010, 7120/8120/9120, and 7230/8230/9230 Combines .............. 111
Checking Voltage Range from Combine Cab (Case 8010) ......................................................... 111
Setting Header Controls (Case 8010)....................................................................................... 113
Checking Voltage Range from Combine Cab (Case IH 5130/6130/7130, 7010/8010;
7120/8120/9120; 7230/8230/9230).............................................................................. 114
Calibrating Auto Header Height Control (Case IH 5130/6130/7130, 7010/8010;
7120/8120/9120; 7230/8230/9230).............................................................................. 117
Calibrating Auto Header Height Control (Case Combines with Version 28.00 or Higher
Software)................................................................................................................... 119
Setting Preset Cutting Height (Case 7010/8010, 7120/8120/9120, 7230/8230/9230) . ..................121
3.8.4 Challenger 6 and 7 Series Combines ........................................................................................122
Checking Voltage Range from Combine Cab (Challenger 6 and 7 Series)...................................122
Engaging Auto Header Height Control (Challenger 6 Series). .....................................................124
Calibrating Auto Header Height Control (Challenger 6 Series)....................................................125
Adjusting Header Height (Challenger 6 Series) .........................................................................127
Adjusting Header Raise/Lower Rate (Challenger 6 Series) ........................................................127
Setting Sensitivity of Auto Header Height Control (Challenger 6 Series)......................................128
3.8.5 Gleaner R62/R72 Combines ....................................................................................................129
System Requirements (Gleaner R62/R72)................................................................................129
Calibrating Auto Header Height Control (Gleaner R62/R72) .......................................................130
Setting Sensitivity of Auto Header Height Control (Gleaner R62/R72 Series)...............................130
3.8.6 Gleaner R65/R66/R75/R76 and S Series Combines (Except S9 Series) ......................................133
Checking Voltage Range from Combine Cab (Gleaner R65/R66/R75/R76 and S Series) .............133
Engaging Auto Header Height Control (Gleaner R65/R66/R75/R76 and S Series) .......................134
Calibrating Auto Header Height Control (Gleaner R65/R66/R75/R76 and S Series) .....................135
Turning Accumulator Off (Gleaner R65/R66/R75/R76 and S Series)...........................................137
Adjusting Header Raise/Lower Rate (Gleaner R65/R66/R75/R76 and S Series)..........................137
Adjusting Ground Pressure (Gleaner R65/R66/R75/R76 and S Series).......................................138
Adjusting Sensitivity of Auto Header Height Control (Gleaner R65/R66/R75/R76 and
S Series) . ..................................................................................................................139
Troubleshooting Alarms and Diagnostic Faults (Gleaner R65/R66/R75/R76 and
S Series) . ..................................................................................................................140
3.8.7 Gleaner S9 Series Combines ...................................................................................................142
Setting up Header (Gleaner S9 Series) ....................................................................................142
Setting up Reel Settings (Gleaner S9 Series)............................................................................146
Setting up Automatic Header Controls (Gleaner S9 Series)........................................................148
Calibrating Header (Gleaner S9 Series) ...................................................................................150
Operating with a Gleaner S9 Series Combine ...........................................................................153
Header In-Field Settings .........................................................................................................155
3.8.8 John Deere 50 Series Combines ..............................................................................................156
Output Voltage Range.............................................................................................................156
Calibrating Auto Header Height ...............................................................................................160
Setting Sensitivity of Auto Header Height Control ......................................................................162
Adjusting Threshold for Drop Rate Valve ..................................................................................163
Operating Auto Header Height.................................................................................................164
3.8.9 John Deere 60 Series Combines ..............................................................................................165
TABLE OF CONTENTS