MacDon FD75 - Page 12

214323 x Revision A
Checking Voltage Range from Combine Cab (John Deere 60 Series) .........................................165
Calibrating Auto Header Height Control (John Deere 60 Series).................................................167
Turning Accumulator Off (John Deere 60 Series) ......................................................................169
Setting Sensing Grain Header Height to 50 (John Deere 60 Series)............................................169
Setting Sensitivity of Auto Header Height Control (John Deere 60 Series) ...................................170
Adjusting Threshold for Drop Rate Valve (John Deere 60 Series) ...............................................171
3.8.10 John Deere 70 Series Combines ............................................................................................172
Checking Voltage Range from Combine Cab (John Deere 70 Series) .........................................172
Calibrating Feeder House Speed (John Deere 70 Series) ..........................................................175
Calibrating Auto Header Height Control (John Deere 70 Series).................................................175
Setting Sensitivity of Auto Header Height Control (John Deere 70 Series) ...................................177
Adjusting Manual Header Raise/Lower Rate (John Deere 70 Series)..........................................177
3.8.11 John Deere S and T Series Combines.....................................................................................178
Checking Voltage Range from Combine Cab (John Deere S and T Series) .................................178
Calibrating Feeder House Fore/Aft Tilt Range (John Deere S and T Series) ................................181
Calibrating Auto Header Height Control (John Deere S and T Series) .........................................184
Setting Sensitivity of Auto Header Height Control (John Deere S and T Series) ...........................186
Adjusting Manual Header Raise/Lower Rate (John Deere S and T Series) .... ..............................187
Setting Preset Cutting Height (John Deere S and T Series)........................................................188
3.8.12 John Deere S7 Series Combines............................................................................................191
Setting up Header (John Deere S7 Series) ...............................................................................191
Checking Sensor Voltage Range (John Deere S7 Series) ..........................................................194
Calibrating Feeder House (John Deere S7 Series) ....................................................................197
Calibrating Header (John Deere S7 Series) ..............................................................................199
3.8.13 CLAAS 500 Series Combines.................................................................................................202
Auto Header Height Sensor Voltage Requirements ...................................................................202
Checking Sensor’s Output Voltage Range ................................................................................202
Adjusting Voltage Limits ..........................................................................................................203
Calibrating Auto Header Height Control (CLAAS 500 Series) .....................................................204
Setting Cutting Height (CLAAS 500 Series) ..............................................................................206
Setting Preset Cutting Height (CLAAS 500 Series) ....................................................................206
Setting Cutting Height Manually (CLAAS 500 Series) ................................................................207
Setting Sensitivity of Auto Header Height Control (CLAAS 500 Series) .......................................208
Adjusting Auto Reel Speed (CLAAS 500 Series) ....................................................................... 211
3.8.14 CLAAS 700 Series Combines.................................................................................................214
Auto Header Height Sensor Voltage Requirements ...................................................................214
Checking Sensor’s Output Voltage Range ................................................................................214
Adjusting Voltage Limits ..........................................................................................................216
Calibrating Auto Header Height Control (CLAAS 700 Series) .....................................................216
Setting Cutting Height (CLAAS 700 Series) ..............................................................................219
Setting Sensitivity of Auto Header Height Control (CLAAS 700 Series) .......................................219
Adjusting Auto Reel Speed (CLAAS 700 Series) .......................................................................221
3.8.15 New Holland Combines CX/CR Series (CR Series – Model Year 2014 and Earlier) ....................223
Checking Voltage Range from Combine Cab (New Holland) ......................................................223
Engaging Auto Header Height Control (New Holland CR/CX Series) ..........................................225
Calibrating Auto Header Height Control (New Holland CR/CX Series) ........................................226
Adjusting Header Raise Rate (New Holland CR/CX Series) .......................................................228
Setting Header Lower Rate to 50 (New Holland CR/CX Series) ....
..............................................229
Setting Sensitivity of Auto Header Height Control to 200 (New Holland CR/CX Series).................229
Setting Preset Cutting Height (New Holland CR/CX Series) .......................................................230
Configuring Reel Fore-Aft, Header Tilt, and Header Type (New Holland CR Series).....................231
3.8.16 New Holland Combines (CR Series – Model Year 2015 and Later) ............................................233
TABLE OF CONTENTS