(9) In st all instr umen t panel top cover and screws.
(Fig. 15)
(10) Install right out er a nd in ner air nozzles. (F ig.
13)
(11) In st all right side cover and scr ews.
(12) Wra p protect ive mat ar ound connect ors
behind in st rument cluster.
(13) Install left outer and inner a ir nozzles.
(14) Install left side cover and screws.
(15) Install passenger side air nozzle cover and
bracket and install the scr ews. (Fig. 12)
(16) Posit ion P ower Dist ribu tion Center (PDC) in
vehicle and connect elect rica l connectors. (Fig. 11)
(17) Install PDC and install bolt a nd nu t. (Fig. 10)
(18) Install PDC grou nd cable an d n ut.
(19) Install steering colum n sh roud and in st all t he
two screws and one nut. (Fig. 9)
(20) Install PDC cover an d twist lock 1/4 turn to
secure in place. (Fig. 8)
(21) Connect electrical connectors and cables to air
conditioning push -button m odu le and in st all. (Fig. 7)
(22) Install center bezel. (Refer to 23 - BODY/IN-
STRUME NT PANEL/INSTRUMENT PANEL CEN-
TER BE ZEL - INSTALLATION)
(23) Install left and r igh t spea ker s. (Refer to 8 -
ELECTRICAL/AUDIO/SPEAKER - INSTALLATION)
(24) Install pa ssen ger airbag. (Refer to8-ELEC-
TRICAL/RESTRAINTS/PASSE NGE R AIRBAG -
INSTALLATION)
(25) Install instr umen t cluster. (Refer to8-ELEC-
TRICAL/INSTRUME NT CLUSTER - INSTALLA-
TION )
(26) Install cup holder. (Refer to 23 - BODY/IN-
STRUME NT PANEL/CUP HOLDER - INSTALLA-
TION )
(27) Install glove compart ment . (Refer to 23 -
BODY/INSTRUMENT PANEL/GLOVE BOX -
INSTALLATION)
(28) Install radio. (Refer to 8 - ELECTRICAL/AU-
DIO/RADIO - INSTALLATION)
(29) Connect ba tter y negat ive cable.
TOP COVER - CLUSTER
REMOVAL
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Remove the screws and u sing a trim stick
C-4755 or equivalent, remove th e cover. (Fig. 23)
INSTALLATION
WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, DISABLE THE AIRBAG SYSTEM BEFORE
ATTEMPTING ANY STEERING WHEEL, STEERING
COLUMN, SEAT BELT TENSIONER, OR INSTRU-
MENT PANEL COMPONENT DIAGNOSIS OR SER-
VICE. DISCONNECT AND ISOLATE THE BATTERY
NEGATIVE (GROUND) CABLE, THEN WAIT TWO
MINUTES FOR THE AIRBAG SYSTEM CAPACITOR
TO DISCHARGE BEFORE PERFORMING FURTHER
DIAGNOSIS OR SERVICE. THIS IS THE ONLY SURE
WAY TO DISABLE THE AIRBAG SYSTEM. FAILURE
TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.
(1) Position the cover an d insta ll the scr ews.
Fig. 23 Instrument Cluster Remove/Install
1 - SCREW (2)
2 - COVER
3 - SCREW (2)
4 - INSTRUMENT CLUSTER
5 - LOOP (2)
23 - 64 INSTRUMENT PANEL VA
To Next Page
Loading...
