Lexmark X95 series - Page 1146

I-6 Service Manual
7558-xxx
Go Back
Previous
Next
sensor (upper media bin full) 4-405
sensor (upper media exit) 4-406
stacker bin lift motor assembly 4-407
stacker media bin assembly 4-410
stapler unit assembly 4-410
stapler unit frame 4-412
stepper motor and belt (buffer/transport) 4-414
stepper motor and belt (entrance/paddle) 4-416
stepper motor and belt (exit) 4-417
sub paddle 4-419
switch (eject cover interlock) 4-419
switch (finisher front door interlock) 4-420
top cover 4-421
upper media bin assembly 4-422
upper media bin front cover 4-423
upper media exit pinch roll assembly 4-423
upper media exit roll assembly 4-424
upper pinch guide assembly 4-426
upper transport roll 4-427
removals, HCF
HCF caster
4-429
HCF controller card PCBA 4-429
HCF feed lift gear bracket 4-430
HCF feed lift motor 4-430
HCF feed roll assembly 4-431
HCF feed unit 4-432
HCF left cover 4-432
HCF lift cables 4-433
HCF media long edge guide assembly 4-434
HCF media out actuator 4-435
HCF media tray assembly 4-436
HCF media tray front cover 4-437
HCF media tray lift coupling assembly 4-438
HCF pick roll assembly 4-439
HCF pick roll shaft assembly 4-439
HCF rear cover 4-441
HCF sensor (HCF media size) 4-441
HCF sensor (HCF media tray set) 4-442
HCF sensor (tray 5 feedout) 4-443
HCF separation drive gear kit 4-444
HCF separation roll assembly 4-445
HCF separation roll shaft assembly 4-446
HCF top cover 4-446
HCF top door assembly 4-447
HCF transport motor 4-449
HCF transport roller kit 4-449
HCF tray lift gear bracket 4-450
sensor (HCF docking interlock) 4-451
sensor (HCF top door interlock) 4-452
sensor (tray 5 media level) 4-453
sensor (tray 5 media out) 4-454
sensor (tray 5 pre feed) 4-455
removals, printer
1st transfer conductor housing
4-24
1st transfer retract clutch assembly 4-26
2nd transfer roller 4-28
ATC sensor PCB 4-30
ATC sensor PCB bracket 4-29
bridge PCBA 4-32
C toner auger 4-35
charge roll HVPS cooling fan 4-38
charge roll HVPS PCBA 4-40
CMYK toner dispense auger assembly 4-41
controller cooling fan 4-44
developer carrier 4-46
developer housing (C) 4-49
developer housing (K) 4-55
developer housing (M) 4-61
developer housing (Y) 4-67
developer housing rear plunger 4-73
developer HVPS PCBA 4-75
feeder slide guide 4-77
front left cooling fan 4-78
front right cooling fan 4-80
front upper cooling fan 4-82
fuser assembly 4-84
fuser cooling fan 4-84
fuser driver PCBA 4-90
fuser driver PCBA cooling fan 4-87
fuser pressure roll retract motor 4-94
fuser/lower redrive/1st BTR retract motor 4-97
inner cover 4-4
inner plate 4-98
internal rear cover 4-6
K toner auger 4-100
LED printhead 4-102
left rear lower cover 4-7
left upper cover 4-7
lower engine PCBA 4-104
lower redrive shift motor assembly 4-105
LVPS front fan guide 4-111
LVPS PCBA 4-112
LVPS sub cooling fan 4-115
M toner auger 4-116
main power GFI interface 4-119
main power switch 4-121
media feed lift motor 4-121
media out actuator 4-123
media size switch PCB 4-123
media transport/MPF drive motor 4-124
MPF roller 4-127
MPF top cover 4-8
MPF tray feeder 4-128
operator panel assembly 4-129
operator panel front cover (MFP) 4-8
operator panel left cover 4-10
operator panel PCBA (MFP) 4-131
operator panel right cover 4-11
operator panel speaker (MFP) 4-132
operator panel top cover (MFP) 4-11
PC smart chip socket (C, M, Y, K) 4-134
PC/developer drive motor 4-138
PC/developer drive motor cooling fan 4-136
pick roller 4-141
printer front door 4-13
printer left duplex door assembly 4-142
printer media turn guide 4-143
printer right cover 4-14