Oval EL4101 - ⑤ Analog Output Low Limit Setup (LOW LIMIT (Ma)); ⑥ Analog Output Low Cutoff Setup (LOW CUT); ⑦ Analog Output Smoothing Factor Setup (SMOOTHING COEF.)

                     
／                    
−−−−−＜ＳＥＴ ＭＯＤＥ＞−−−−−−

ＡＮＡＬＯＧ ＯＵＴＰＵＴ       


ＬＯＷ ＬＩＭＩＴ（ｍＡ）      
         ＋４．０００００ Ｅ＋０
                     
                     
                     
＋４．０００００  
       Ｅ＋０
−−−−−−−＜ＩＮＰＵＴ＞−−−−−−−
     ｜ＣＡＮ−｜    ｜     
 ＥＸＩＴ｜ ＣＥＬ｜ＣＬＥＲ｜ＥＮＴＲ 
                     
／                    
−−−−−＜ＳＥＴ ＭＯＤＥ＞−−−−−−

ＡＮＡＬＯＧ ＯＵＴＰＵＴ       


ＬＯＷ ＣＵＴ            
         ＋０．０００００ Ｅ＋０
                     
                     
                     
＋０．０００００  
       Ｅ＋０
−−−−−−−＜ＩＮＰＵＴ＞−−−−−−−
     ｜ＣＡＮ−｜    ｜     
 ＥＸＩＴ｜ ＣＥＬ｜ＣＬＥＲ｜ＥＮＴＲ
                     
／                    
−−−−−＜ＳＥＴ ＭＯＤＥ＞−−−−−−

ＡＮＡＬＯＧ ＯＵＴＰＵＴ       


ＳＭＯＯＴＨＩＮＧ ＣＯＥＦ．
         ＋８．７５０００ Ｅ−１
                     
                     
                     
＋８．７５０００  
       Ｅ−１
−−−−−−−＜ＩＮＰＵＴ＞−−−−−−−
     ｜ＣＡＮ−｜    ｜     
 ＥＸＩＴ｜ ＣＥＬ｜ＣＬＥＲ｜ＥＮＴＲ
E-880TM-3-E

⑤ Analog output low limit setup (LOW LIMIT (mA))
The low limit of analog output is set up here.
Analog output submenu screen p. 76
⑥ Analog output low cutoff setup (LOW CUT)
The low cutoff level of analog output is set up here.
※ This item is shown only in Model EL4401. It is not shown in other models.
⑦ Analog output smoothing factor setup (SMOOTHING COEF.)
The smoothing factor of analog output is set up here.
Smoothing facto K=1－
1
Time constant (s)
※ Time constant is the time required for the indicated reading to reach 63% of the final level;
it reaches 86% after in twice the time duration of time constant and 95% in three times the
time duration of time constant.
←Numerical value input setup
For details of numerical value input setup, see “(1) Numerical value setup screen
(INPUT)” on page 43.
※ The unit to be set up here is mA. Make sure of the unit before you set up.
←Numerical value input setup
For details of numerical value input setup, see “(1) Numerical value setup screen
(INPUT)” on page 43.
※ For the unit to be set here, the unit set at the analog output unit setup
(① Analog output unit setup (UNIT) on page 77) is used. Make sure of the
unit before you set up.
←Numerical value input setup
For details of numerical value input setup, see “(1) Numerical value setup screen
(INPUT)” on page 43.
※ Do not enter a negative value in the integer part of setting, or it will cause
erratic operation.
Analog output submenu screen p. 76
Analog output submenu screen p. 76