Santerno Sinus Penta - Page 10

SINUS PENTA
PROGRAMMING GUIDE
10/486
Table 55: MDO parameterization for the Ready state of a PLC supervisor .................................................................... 202
Table 56: List of parameters P270 to P305 .................................................................................................................... 203
Table 57: List of parameters P306 to P317 .................................................................................................................... 217
Table 58: List of parameters P318 to P325 .................................................................................................................... 221
Table 59: List of parameters P330 to P331 .................................................................................................................... 224
Table 60: List of the programmable measurements in P330 ÷ P331 .............................................................................. 225
Table 61: Virtual Digital Output Modes ........................................................................................................................... 227
Table 62: Test functions .................................................................................................................................................. 228
Table 63: MPL parameterization for Dry Run Detection.................................................................................................. 233
Table 64: MPL parameterization for Pipe Fill function .................................................................................................... 235
Table 65: List of parameters P350 to P385 .................................................................................................................... 236
Table 66: Analog input hardware mode .......................................................................................................................... 250
Table 67: List of parameters P390 to P399 .................................................................................................................... 251
Table 68: Programmable “Motor Tune” functions ........................................................................................................... 256
Table 69: List of inputs I073 - I074 ................................................................................................................................. 258
Table 70: Maximum value of the output frequency depending on the Penta model ....................................................... 260
Table 71: List of parameters C001 to C004 .................................................................................................................... 261
Table 72: Description of the parameters classified by motor .......................................................................................... 264
Table 73: Motor ratings ................................................................................................................................................... 264
Table 74: Parameters of the equivalent circuit of the asynchronous machine ................................................................ 265
Table 75: Motor parameters used by control algorithms ................................................................................................. 265
Table 76: IFD control parameters for the connected motors .......................................................................................... 267
Table 77: Parameters setting Slip Compensation (IFD Control) ..................................................................................... 268
Table 78: List of parameters C008 to C128 .................................................................................................................... 274
Table 79: Equivalence between AC mains range and DC range .................................................................................... 276
Table 80: Word bits for address 1012, (1055, 1098) ..................................................................................................... 279
Table 81: Parameters depending on the Drive Size and Model / Class 2T/4T / 1 .......................................................... 289
Table 82: Parameters depending on the Drive Size and Model - Class 2T/4T / 2 .......................................................... 291
Table 83: Parameters depending on the Drive Size and Model - Class 2T/4T / 3 .......................................................... 293
Table 84: Parameters depending on the Drive Size and Model - Class 2T/4T /4 ........................................................... 295
Table 85: Parameters depending on the Drive Size and Model - Class 5T/6T / 1 .......................................................... 297
Table 86: Parameters depending on the Drive Size and Model - Class 5T/6T / 2 .......................................................... 298
Table 87: Parameters depending on the Drive Size and Model - Class 5T/6T / 3 .......................................................... 299
Table 88: Parameters depending on the Drive Size and Model - Class 5T/6T / 4 .......................................................... 300
Table 89: List of parameters C043 to C135 .................................................................................................................... 303
Table 90: Enable conditions of the control sources ........................................................................................................ 307
Table 91: Remote command inputs from serial link ........................................................................................................ 308
Table 92: Enable conditions of the reference sources .................................................................................................... 309
Table 93: Reference inputs from serial link ..................................................................................................................... 310
Table 94: List of parameters C140 to C148 .................................................................................................................... 315
Table 95: Unprogrammable functions ............................................................................................................................. 319
Table 96: Terminals used for other inputs ...................................................................................................................... 319
Table 97: Terminal board: Factory-setting ...................................................................................................................... 325
Table 98: List of parameters C149 to C188c and I006 ................................................................................................... 326
Table 99: Address 1154 bits ........................................................................................................................................... 333
Table 100: Multispeed selection ..................................................................................................................................... 334
Table 101: Selected Speed reference ............................................................................................................................ 334
Table 102: Multiramp selection ....................................................................................................................................... 337
Table 103: Selected ramp ............................................................................................................................................... 337
Table 104: Motor selection .............................................................................................................................................. 341
Table 105: Selection of the speed reference variation .................................................................................................... 342
Table 106: Variation of the selected speed reference .................................................................................................... 342
Table 107: Multitorque selection ..................................................................................................................................... 348
Table 108: Selected Multitorque reference ..................................................................................................................... 348
Table 109: Selection of PID Multireferences ................................................................................................................... 349
Table 110: List of parameters C189 to C199 .................................................................................................................. 354
Table 111: Coding of C189 ............................................................................................................................................. 355
Table 112: Coding of C199 ............................................................................................................................................. 357
Table 113: List of parameters C210 to C213d ................................................................................................................ 360
Table 114: List of parameters C215 to C224 .................................................................................................................. 369
Table 115: List of parameters C225 to C235 .................................................................................................................. 374
Table 116: List of parameters C245 to C250 .................................................................................................................. 381
Table 117: List of parameters C255 to C258 .................................................................................................................. 384
Table 118: Suggested values for the motor thermal time constant ................................................................................. 387
Table 119: Typical datasheet for 4-pole, 50Hz-400V motors .......................................................................................... 388
Table 120: List of parameters C264 to C274 .................................................................................................................. 391
Table 121: List of parameters C275 to C278 .................................................................................................................. 393
Table 122: Reference sources from serial link ................................................................................................................ 397