YOKOGAWA DLM4000 Series User Manual

Index-1
IM DLM4038-02EN
Index
CAN bus trigger .................................................................... 2-20
CAN FD bus trigger .............................................................. 2-24
CAN FD serial bus signals, analyzing and searching ........... 12-9
CAN serial bus signals, analyzing and searching................. 12-5
channels, loading waveform data into ................................ 17-10
character strings, entering ....................................................... viii
chip select source, SPI bus, analyzing and searching ....... 12-54
chip select source, SPI bus trigger ....................................... 2-56
chip select source, user-defined bus, analyzing
and searching .................................................................. 12-59
chip select source, user-defined bus trigger ......................... 2-60
CH menu ................................................................................ 1-1
class setup, harmonic analysis ............................................. 14-6
clear trace ............................................................................... 4-4
click sound, turning on and off .............................................. 19-1
color ........................................................................................ 4-2
combination, B TRIG ............................................................ 2-63
combination trigger ............................................................... 2-63
computation conditions ..........................................................6-11
computation mode .................................................................. 6-1
condition, CAN FD bus trigger .............................................. 2-29
conditions, edge trigger with ................................................... 2-7
condition setup, CAN bus trigger ................................. 2-22, 2-23
condition setup, CAN FD bus trigger ........................... 2-27, 2-28
condition setup, CXPI bus search ...................................... 12-22
condition setup, edge search.................................................11-2
condition setup, FlexRay bus trigger ........................... 2-18, 2-19
condition setup, I2C bus trigger ............................................ 2-52
condition setup, LIN bus trigger ................................... 2-32, 2-33
condition setup, PSI5 search .............................................. 12-37
condition setup, PSI5 trigger ................................................ 2-44
condition setup, pulse width search.....................................11-11
condition setup, SENT trigger .............................2-37, 2-38, 2-39
condition setup, SPI bus trigger............................................ 2-57
condition setup, state search .................................................11-8
condition setup, state width search .....................................11-14
condition setup, UART trigger .............................................. 2-47
condition setup, user-defined bus trigger ............................. 2-58
continuous .............................................................................. 9-6
count computation .................................................................. 6-6
count type ............................................................................... 6-7
CS (SS), SPI bus, analyzing and searching ....................... 12-53
CS (SS), SPI bus trigger....................................................... 2-56
CS, user-defined bus, analyzing and searching ................. 12-59
CS, user-defined bus trigger................................................. 2-60
cursor jumping ........................................................................ 8-1
cursor measurement........................................................ 5-2, 8-1
CURSOR menu ...................................................................... 8-1
cursor movement ................................................................ 17-14
cursor positions, setting .......................................................... 8-1
cursor type, FFT ..................................................................... 7-3
CXPI serial bus signals, analyzing and searching .............. 12-17
cycle ....................................................................................... 9-8
cycle mode .................................................................... 9-2, 14-4
cyclic statistical processing..................................................... 9-8
D
Page
data compression ................................................................. 17-4
data frame source................................................................. 2-43
data mode, PSI5 search ..................................................... 12-37
data mode, PSI5 trigger........................................................ 2-44
data mode, UART trigger ...................................................... 2-47
data type to load ................................................................. 17-12
Symbols
Page
ΔTcursor ................................................................................ 8-1
ΔT&ΔVcursor ......................................................................... 8-3
ΔVcursor ................................................................................ 8-2
Numerics
Page
1000BASE-T port ................................................................. 18-1
A
Page
A -> B(N) ............................................................................... 2-64
accumulation display .............................................................. 4-3
ACQUIRE menu ..................................................................... 3-1
acquisition mode..................................................................... 3-1
action .................................................................................... 2-67
Action Go/Nogo menu .......................................................... 2-68
action-on-trigger ................................................................... 2-67
Action on Trig menu.............................................................. 2-67
addition, subtraction, and multiplication.................................. 6-2
A Delay B .............................................................................. 2-63
Adr Data mode ..................................................................... 2-51
ANALYSIS histogram menu ........................................ 13-1, 13-2
ANALYSIS menu .................................................................. 14-1
ANALYSIS Power Analysis menu, harmonics ...................... 14-6
ANALYSIS Power Analysis menu, I2t ................................... 14-8
ANALYSIS Power Analysis menu, SOA ............................... 14-5
ANALYSIS Power Analysis menu, SW Loss ........................ 14-2
ANALYSIS Power Measurement menu .............................. 14-10
angle cursor ............................................................................ 8-5
applicable class .................................................................... 14-6
area (XY) ................................................................................ 5-3
A trigger ................................................................................ 2-65
automated measurement of waveform parameters, saving . 17-8
automatically measured values, processing statistics on ....... 9-6
auto naming .......................................................................... 17-3
auto scrolling ........................................................................ 10-1
auto setup, CAN bus ............................................................ 12-6
auto setup, CAN FD bus..................................................... 12-10
auto setup, CXPI bus.......................................................... 12-18
auto setup, FlexRay bus ....................................................... 12-2
auto setup, I2C bus ............................................................ 12-46
auto setup, LIN bus ............................................................ 12-14
auto setup, PSI5 ................................................................. 12-32
auto setup, SENT ............................................................... 12-25
auto setup, SPI bus ............................................................ 12-52
auto setup, UART ............................................................... 12-40
B
Page
backlight, adjusting ................................................................. 4-5
bandwidth limit ........................................................................ 1-4
bit setup, LOGIC(A|B) ........................................................... 1-12
bit setup, LOGIC(L) ................................................................ 1-7
Break Synch mode ............................................................... 2-31
broadcasting system............................................................. 2-61
B trigger ................................................................................ 2-65
B TRIG menu ........................................................................ 2-63
built-in printer ........................................................................ 16-1
built-in printer, printing on ..................................................... 16-3
C
Page
cable ..................................................................................... 18-1
calc setup ............................................................................. 9-10

YOKOGAWA DLM4000 Series Specifications

General

Brand	YOKOGAWA
Model	DLM4000 Series
Category	Test Equipment
Language	English