Cisco ASR 1004 Hardware Installation Guide

◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50 in./394 mm
to 19.00 in./482.6 mm
•
Cisco ASR 1004 Router:
◦
Chassis height meets EIA-310 rack spacing 4RU (6.95 in./176.53 mm), universal rack-mount
◦
Chassis width meets EIA-310 19-in. (17.25 in./438.15 mm) wide with rack brackets
◦
Cable-management brackets at each Cisco ASR 1000 Series SPA Interface (SIP) locations can
hold 16 ports of STP/UTP RJ 45 cables
◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50 in./394 mm
to 19.00 in. /482.6 mm
•
Cisco ASR 1006 Router:
◦
Chassis height meets EIA-310 rack spacing 6RU (10.47 in./266 mm), universal rack-mount
◦
Chassis width meets EIA-310 19-in. (17.25 in./438.15 mm) wide with rack brackets
◦
Cable-management brackets at each Cisco ASR 1000 Series SPA Interface (SIP) locations can
hold 16 ports of STP/UTP RJ 45 cables
◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50/394mm to
19.00/482.6mm
•
Cisco ASR 1013 Router:
◦
Chassis height meets EIA-310 rack spacing 13RU (22.8 in./579.12 mm), universal rack-mount
◦
Chassis width meets EIA-310 19-in. (17.25 in./438.15 mm) wide with rack brackets
◦
Cable-management brackets allow a bend radius of 1.5 in. (38.1 mm) for cables
◦
Adjustable rack-mount brackets allow for a front to rear rail variance distance of 15.50/394mm to
19.00 in./482.6 mm
◦
Ships with forward rack-mount brackets installed and an extra set in the accessory kit
Floor Loading Considerations
Ensure that the floor under the rack supporting the Cisco 1000 Series Routers is capable of supporting the
combined weight of the rack and all other installed equipment.
To assess the weight of the fully configured Cisco 1000 Series Router respectively, refer to the table in Physical
Characteristics, on page 120 section.
For additional information about floor loading requirements, consult the document GR-63-CORE, Network
Equipment Building System (NEBS) Requirements: Physical Protection .
Cisco ASR 1000 Series Router Hardware Installation Guide
122
Preparing Your Site for Installation
Floor Loading Considerations

Cisco ASR 1004 Specifications

General

Product Type	Router
Form Factor	Rack-mountable
Rack Height	2U
Forwarding Capacity	Up to 20 Gbps
Total Number of Ports	Varies by configuration
Number of Total Expansion Slots	4
Product Series	ASR 1000
Model	ASR 1004
Forwarding Performance	Up to 20 Gbps
Operating System	Cisco IOS XE
Power Supply	Dual
Route Processor	ASR 1000 Series Route Processor
Network Interface Modules	SFP, SFP+, Gigabit Ethernet, 10 Gigabit Ethernet
Interfaces/Ports	Varies by configuration
Expansion Slot Type	SPA
Throughput	20 Gbps
Redundancy	Power supply, Route Processor
Interfaces	Gigabit Ethernet, 10 Gigabit Ethernet, SFP, SFP+
Storage	Up to 64 GB Flash