Cisco ASR 1004 Hardware Installation Guide

If there are two different versions of the Cisco ASR1000-ESP in a router when you reload, the F0 slot always
comes up as Active and the F1 slot comes up as Standby or Disabled, depending on whether the F1 slot has a
later version of the Cisco ASR1000-ESP or an earlier one. A downgrade from a later version ESP to an earlier
version is not supported and that is the reason the Cisco ASR1000-ESP20 is disabled in this step. To downgrade
back to a Cisco ASR1000-ESP20, you must remove the Cisco ASR1000-ESP40 and reload the router. Similarly,
to downgrade back to a Cisco ASR1000-ESP10 from a Cisco ASR1000-ESP20, you must remove the Cisco
ASR1000-ESP20 and reload the router.
Note
Removing a Cisco ASR1000-ESP
To remove the Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, Cisco ASR1000-ESP20, or Cisco
ASR1000-ESP40 from the Cisco ASR 1000 Series Routers, follow this procedure:
SUMMARY STEPS
1.
Slip on the ESD-preventive wrist strap that was included in the accessory kit. Loosen the captive screws
on the Cisco ASR 1000 Series Embedded Services Processor.
2.
Using the handles on both sides of the module, with two hands gently slide the Cisco ASR 1000 Series
Embedded Services Processor (ESP5, ESP10, ESP20, ESP40) out of the chassis slot.
3.
Place the Cisco ASR1000-ESP module on an antistatic surface with its printed circuit board components
facing upward or in a static shielding bag.
DETAILED STEPS
Step 1
Slip on the ESD-preventive wrist strap that was included in the accessory kit. Loosen the captive screws on the Cisco
ASR 1000 Series Embedded Services Processor.
Step 2
Using the handles on both sides of the module, with two hands gently slide the Cisco ASR 1000 Series Embedded
Services Processor (ESP5, ESP10, ESP20, ESP40) out of the chassis slot.
Handle the Cisco ASR1000-ESP5, Cisco ASR1000-ESP10, Cisco ASR1000-ESP20, or Cisco ASR1000-ESP40
by the carrier edges only; never touch the printed circuit board components or connector pins.
Note
Step 3
Place the Cisco ASR1000-ESP module on an antistatic surface with its printed circuit board components facing upward
or in a static shielding bag.
What to Do Next
You have completed the removal procedure for the Cisco ASR 1000 Series Embedded Services Processor.
from a Cisco ASR1000-ESP.
Replacing the Cisco ASR1000-ESP
To replace the Cisco ASR 1000 Series Embedded Services Processor in the Cisco ASR 1000 Series Router,
follow this procedure:
Cisco ASR 1000 Series Router Hardware Installation Guide
532
Removing and Replacing FRUs from the Cisco ASR 1000 Series Routers
Removing a Cisco ASR1000-ESP

Cisco ASR 1004 Specifications

General

Product Type	Router
Form Factor	Rack-mountable
Rack Height	2U
Forwarding Capacity	Up to 20 Gbps
Total Number of Ports	Varies by configuration
Number of Total Expansion Slots	4
Product Series	ASR 1000
Model	ASR 1004
Forwarding Performance	Up to 20 Gbps
Operating System	Cisco IOS XE
Power Supply	Dual
Route Processor	ASR 1000 Series Route Processor
Network Interface Modules	SFP, SFP+, Gigabit Ethernet, 10 Gigabit Ethernet
Interfaces/Ports	Varies by configuration
Expansion Slot Type	SPA
Throughput	20 Gbps
Redundancy	Power supply, Route Processor
Interfaces	Gigabit Ethernet, 10 Gigabit Ethernet, SFP, SFP+
Storage	Up to 64 GB Flash