Reflex Variomat Touch VS 2-1/60 Original Operating Manual

Contents
Variomat Touch — 09.09.2022-Rev. C English —
27
Contents
English
Variomat Touch
09.09.2022-Rev. C
englisch
1 Notes on the operating manual .............................................28
2 Liability and guarantee ...........................................................28
3 Safety .......................................................................................28
3.1 Explanation of symbols ......................................................................... 28
3.1.1 Symbols and notes used ...................................................... 28
3.2 Personnel requirements ....................................................................... 28
3.3 Personal protective equipment ........................................................... 28
3.4 Intended use .......................................................................................... 28
3.5 Inadmissible operating conditions ...................................................... 28
3.6 Residual risks .......................................................................................... 28
4 Description of the device ........................................................29
4.1 Description ............................................................................................. 29
4.2 Overview................................................................................................. 29
4.3 Identification .......................................................................................... 29
4.3.1 Nameplate ............................................................................. 29
4.3.2 Type code .............................................................................. 29
4.4 Function .................................................................................................. 29
4.5 Scope of delivery ................................................................................... 30
4.6 Optional equipment and accessories .................................................. 30
5 I/O module (optional expansion module) .............................30
5.1 Technical data ........................................................................................ 30
5.2 Settings ................................................................................................... 31
5.2.1 Terminator settings in RS-485 networks ............................ 31
5.2.2 Setting the module address ................................................ 31
5.2.3 I/O module default settings ................................................. 32
5.3 Replacing the fuses ............................................................................... 32
6 Technical data .........................................................................33
6.1 Control unit ............................................................................................ 33
6.2 Tanks ....................................................................................................... 33
7 Installation ...............................................................................33
7.1 Installation conditions .......................................................................... 34
7.1.1 Incoming inspection ............................................................. 34
7.2 Preparatory work ................................................................................... 34
7.3 Execution ................................................................................................ 34
7.3.1 Positioning ............................................................................ 34
7.3.2 Installation of add-on components for the tanks ............. 34
7.3.3 Tank installation ................................................................... 34
7.3.4 Hydraulic connection ........................................................... 35
7.3.5 Fitting the thermal insulation ............................................. 36
7.3.6 Installation of the weight measuring cell .......................... 36
7.4 Switching and make-up variants ......................................................... 37
7.4.1 Function ................................................................................. 37
7.5 Electrical connection ............................................................................. 38
7.5.1 Terminal diagram ................................................................. 38
7.5.2 Terminal plan, connection component .............................. 38
7.5.3 Terminal plan, operating unit ............................................. 39
7.5.4 RS-485 interface .................................................................... 39
7.6 Installation and commissioning certificate......................................... 40
8 Commissioning ....................................................................... 40
8.1 Checking the requirements for commissioning ................................. 40
8.2 Variomat switching points ................................................................... 40
8.3 Modifying the controller's start routine .............................................. 40
8.4 Filling the tanks with water ................................................................. 41
8.4.1 Filling with a hose ................................................................ 41
8.4.2 Filling with the solenoid valve in the make-up ................. 41
8.5 Venting the pump ................................................................................. 42
8.6 Parametrising the controller in the Customer menu ........................ 42
8.7 Starting Automatic mode ..................................................................... 42
9 Operation ................................................................................ 42
9.1.1 Automatic mode ................................................................... 42
9.1.2 Manual mode ........................................................................ 42
9.1.3 Stop mode ............................................................................. 43
9.1.4 Summer operation ............................................................... 43
9.2 Restarting ............................................................................................... 43
10 Controller ................................................................................ 43
10.1 Operator panel ...................................................................................... 43
10.2 Calibrating the touch screen ................................................................ 43
10.3 Configuring settings in the controller ................................................. 44
10.3.1 Customer menu .................................................................... 44
10.3.2 Service menu ........................................................................ 44
10.3.3 Default settings .................................................................... 45
10.3.4 Setting degassing programmes.......................................... 45
10.3.5 Degassing programmes – overview ................................... 45
10.4 Messages ................................................................................................ 46
11 Maintenance ........................................................................... 47
11.1 Maintenance schedule .......................................................................... 47
11.1.1 Cleaning the dirt trap ........................................................... 48
11.1.2 Cleaning the tanks................................................................ 48
11.2 Checking switching points ................................................................... 48
11.3 Inspection .............................................................................................. 49
11.3.1 Pressure-bearing components ............................................ 49
11.3.2 Inspection prior to commissioning ..................................... 49
11.3.3 Inspection intervals .............................................................. 49
12 Disassembly ............................................................................ 49
13 Annex ...................................................................................... 49
13.1 Reflex Customer Service ....................................................................... 49
13.2 Conformity and standards .................................................................... 49
13.3 Guarantee .............................................................................................. 49
ivz_en

Reflex Variomat Touch VS 2-1/60 Specifications

General

Brand	Reflex
Model	Variomat Touch VS 2-1/60
Category	Control Systems
Language	English