Remote control commands
R&S
®
RTP
1529User Manual 1337.9952.02 ─ 12
TJTRack1 | DJTRack1 | DDJTrack1 | PJTRack1 | RJOTrack1 |
TJSPectrum1 | DDJSpectrum1 | PJSPectrum1 |
RJOSpectrum1 | SEYE1 | BATHtub2 | BMEas2 | SRESponse2 |
SRHist2 | SDHist2 | TJHist2 | DJHist2 | DDJHist2 | PJHist2 |
RJOHist2 | SRTRack2 | SDTRack2 | TJTRack2 | DJTRack2 |
DDJTrack2 | PJTRack2 | RJOTrack2 | TJSPectrum2 |
DDJSpectrum2 | PJSPectrum2 | RJOSpectrum2 | SEYE2 |
NBAThtub1 | NBMeas1 | TNHist1 | DNHist1 | DDNHist1 |
PNHist1 | RNOHist1 | TNTRack1 | DNTRack1 | DDNTrack1 |
PNTRack1 | RNOTrack1 | TNSPectrum1 | DDNSpectrum1 |
PNSPectrum1 | RNOSpectrum1 | NBAThtub2 | NBMeas2 |
TNHist2 | DNHist2 | DDNHist2 | PNHist2 | RNOHist2 |
TNTRack2 | DNTRack2 | DDNTrack2 | PNTRack2 |
RNOTrack2 | TNSPectrum2 | DDNSpectrum2 | PNSPectrum2 |
RNOSpectrum2 | PJDHist1 | BUJHist1 | RJHist1 | PJDTrack1 |
PJDSpectrum1 | PJDHist2 | BUJHist2 | RJHist2 | PJDTrack2 |
PJDSpectrum2 | PNDHist1 | BUNHist1 | RNHist1 | PNDTrack1 |
PNDSpectrum1 | PNDHist2 | BUNHist2 | RNHist2 | PNDTrack2 |
PNDSpectrum2
*RST:
C1W1
Example: See Chapter 22.3.5.2, "Exporting waveform data to file",
on page 1133
Usage: Asynchronous command
EXPort:WAVeform:MULTichannel <MltChXpt>
Enables or disables the multichannel export.
If you enable the multichannel export, all active channels are included to the export
data. You can change the export state using the CHANnel<m>:EXPortstate com-
mand.
If multichannel export is disabled, select the waveform to be exported using the
EXPort:WAVeform:SOURce command.
Note that CHANnel<m>[:WAVeform<n>]:DATA[:VALues]? returns the data of all
channels that are selected for export, no matter of the channel suffix.
Parameters:
<MltChXpt> ON | OFF
*RST: OFF
Usage: Asynchronous command
CHANnel<m>:EXPortstate <ExportState>
Includes or excludes the indicated channel in waveform export. The data of channel
waveform 1 is exported.
The commands takes effect if EXPort:WAVeform:MULTichannel is ON.
Data management
To Next Page
Loading...
