Rohde & Schwarz RTP044 - Base Instrument

Remote control commands
R&S
®
RTP
2315User Manual 1337.9952.02 ─ 12
22.27.1 Base instrument
Legacy command Replaced by Comment
BUSFormat For parallel buses:
BUS<m>:PARallel:DATA:FORMat
on page 2204
For serial buses:
BUS<m>:FORMat on page 1549
Replaced since FW 4.70
SEARch:TRIGger:DATatoclock[:STATe]
SEARch:TRIGger:DATatoclock:ACOPy
SEARch:TRIGger:DATatoclock:CEDGe
SEARch:TRIGger:DATatoclock:CLEVel
SEARch:TRIGger:DATatoclock:CSOurce
SEARch:TRIGger:DATatoclock:HTIMe
SEARch:TRIGger:DATatoclock:STIMe
SEARch:TRIGger:SETHold[:STATe]
on page 1483
SEARch:TRIGger:SETHold:ACOPy
on page 1484
SEARch:TRIGger:SETHold:CEDGe
on page 1498
SEARch:TRIGger:SETHold:CLEVel
on page 1499
SEARch:TRIGger:SETHold:CSOurce
on page 1499
SEARch:TRIGger:SETHold:HTIMe
on page 1499
SEARch:TRIGger:SETHold:STIMe
on page 1500
Replaced since FW 5.00
TRIGger<m>:DATatoclock:CSOurce[:VALue]
TRIGger<m>:DATatoclock:CSOurce:EDGE
TRIGger<m>:DATatoclock:CSOurce:LEVel
TRIGger<m>:DATatoclock:HTIMe
TRIGger<m>:DATatoclock:STIMe
TRIGger<m>:SETHold:CSOurce[:VALue]
on page 1272
TRIGger<m>:SETHold:CSOurce:EDGE
on page 1271
TRIGger<m>:SETHold:CSOurce:LEVel
on page 1271
TRIGger<m>:SETHold:HTIMe
on page 1272
TRIGger<m>:SETHold:STIMe
on page 1272
Replaced since FW 5.00
TRIGger<m>:OUT:STATe TRIGger<m>:OUT:ACTion on page 1316 Replaced since FW 5.00
TRIGger<m>:PARallel:DATato-
clock:CSOurce[:VALue]
TRIGger<m>:PARallel:DATato-
clock:CSOurce:EDGE
TRIGger<m>:PARallel:DATatoclock:STIMe
TRIGger<m>:PARallel:DATatoclock:HTIMe
TRIGger<m>:PARallel:SETHold:
CSOurce[:VALue] on page 2210
TRIGger<m>:PARallel:SETHold:
CSOurce:EDGE on page 2213
TRIGger<m>:PARallel:SETHold:HTIMe
on page 2213
TRIGger<m>:PARallel:SETHold:STIMe
on page 2213
Replaced since FW 5.00
TRIGger<m>:SEQuence:MODE TRIGger<m>:SEQuence:TYPE
on page 1310
Replaced since FW 5.10
Deprecated commands