Appendix 3: VDRPARAMS.INI File, Rev. 1.2
VDR-100G3/G3S Installation Manual 18/01/2009
2
A3.4 Storage Parameters
Parameter Typical Value Remarks
primaryLoc “D:\VDR_DATA” Primary recording directory.
mirrorLoc “E:\VDR_DATA_
MIRROR”
Mirror directory recording.
archiveLoc “F:\VDR_DATA_
ARCHIVE”
Archived data directory.
tmpDrive “D:\”
fullDownloadEnabled 1 0=disabled, 1=enabled; default is 1
VideoToFRM 1 0 to 4; default is 1; 0=all video to FRM
hardenedStorage 1 0=disable; 1=enable; 2=Dual; default is 1
hardenedFormat 5 1=L3 HVR; 2=Unused; 3=Jotron; 4=Rutter-
ACR Float-Free, 5=Rutter Fixed; default is 5
secondaryHardenedFormat 4 1=L3 HVR; 2=Unused; 3=Jotron; 4=Rutter-
ACR Float-Free, 5=Rutter Fixed; default is 4
L3HVR-serverPort 5000 default port is 5000
L3HVR-IP 192.168.0.2 default IP is 192.168.0.2
L3HVR-numStreams 3 default is 3
L3HVR-streamName1 "AUDIO"
L3HVR-streamName2 "NMEA"
L3HVR-streamName3 "VIDEO"
L3HVR-errorChecking 1 0=disable; 1=enable; default is 1
L3HVR-compressNMEA 1 0=disable; 1=enable; default is 1
L3HVR-streamType1 "AUDIO" stream type may be AUDIO, VIDEO or NMEA;
L3HVR-streamType2 "NMEA" stream type may be AUDIO, VIDEO or NMEA;
L3HVR-streamType3 "VIDEO" stream type may be AUDIO, VIDEO or NMEA;
NetworkHVR-IP “192.168.0.37” Default is 192.168.0.37; if secondary
FRM=200.200.200.37
NetworHVR-compressNMEA 0 0 = disable, 1=enable; default is 0
NetworkHVR-DriveLetter “X”
NetworkHVR-DataLocation “VDR_DATA”
CACRFFMC-IP “192.168.0.100” Default is 192.168.0.100; if secondary
FRM=200.200.200.100
CACRFFMC-compressNMEA 0 0 = disable, 1=enable; default is 0
RutterFixed-IP 192.168.0.50 Default is 192.168.0.50
RutterFixed-DriveLetter “Z”
RutterFixed-compressNMEA 0 0 = disable, 1=enable; default is 0
Table A3- 4- Storage Parameters
The location of the local data storage is read from the primaryLoc field. If fullDownloadEnabled
is set, all data will be copied. Otherwise, only the basic IMO-required data will be copied. The
tmpDrive field is used by the PMC storage module. It should be set to one of the VDR-100G3
internal fixed disks.
mirrorLoc (E:\) specifies the location of where the most current 12 hours (0-12 hours old) of data
is stored. archiveLoc (F:\) is the location of the auto archived data.
If a hardened memory capsule is connected to the VDR-100G3, the hardenedStorage field must
be set to 1 to enable support. Use Dual if there is a secondary FRM connected to the system,
such as an Rutter-ACR Float-Free capsule. Four types of capsules are supported by the system
– the hardenedFormat field specifies which one is to be used.
To Next Page
Loading...