Rutter VDR-100G3 - Page 324

Appendix 3: VDRPARAMS.INI File, Rev. 1.2
VDR-100G3/G3S Installation Manual 18/01/2009
10
[AUDIO]
blocks =60
// VDR-100G3
ChannelEnabled1 = 1 // 0 = disabled, 1 = enabled
ChannelEnabled2 = 1
ChannelEnabled3 = 1
ChannelEnabled4 = 1
ChannelEnabled5 = 0
ChannelEnabled6 = 0
ChannelEnabled7 = 0
ChannelEnabled8 = 0
// Software mixing - provide list of channels to mix (max. 2 per channel)
// Use comma for OutputChannelx if 2 channels are mixed i.e. 1,2
NumOutputChannels = 4
OutputChannel1 = 1
OutputChannel2 = 2
OutputChannel3 = 3
OutputChannel4 = 4
OutputChannel5 = 5
OutputChannel6 = 6
OutputChannel7 = 7
OutputChannel8 = 8
numVHFChannels = 1 // default is 1
VHF-Channel1 = 1 // default is 1
VHF-Channel2 = 5
MikesOnMixer1 = 2 // 0 to 2; first non-VHF channel
MikesOnMixer2 = 2
MikesOnMixer3 = 2
MikesOnMixer4 = 0
MikesOnMixer5 = 0
MikesOnMixer6 = 0
MikesOnMixer7 = 0
DetectionThreshold1 = 500 // test signal RMS must exceed this to be detected
DetectionThreshold2 = 500 // test signal RMS must exceed this to be detected
DetectionThreshold3 = 500 // test signal RMS must exceed this to be detected
DetectionThreshold4 = 500 // test signal RMS must exceed this to be detected
DetectionThreshold5 = 500 // test signal RMS must exceed this to be detected
DetectionThreshold6 = 500 // test signal RMS must exceed this to be detected
ChirpLength = 30 // mike self-test signal length, in ms (100 ms max)
MikeRetryInterval = 3600 // in seconds
MaxMikeRetrys = 11 // retry this many times before declaring failure
[VIDEO]
numSources = 1 // 1 to 4, default is 2
transferRate = 15000 // 1 video = 15000, 2=7500, 3=5000, 4=3750
blocks = 4
maxColors = 256 // maximum number of colors in output image;
// ignored if enhancedCompression is enabled
enhancedCompression = 0 // 1 = enable, default is 0
noiseClipping = 0 // 1 = enable, default is 1; ignored if enhancedCompression is disabled
recordDuringPowerFail = 0 // To record Video during a power failure, set value to 1; default = 0
[NMEA]
transferRate = 1000 // 500 to 1000 ms, default is 1000
blocks =60
TimeSourcePort = 3 // port that time signal is on, 3 = UDP, 1 or 2 = Serial Port
timeString = ZDA // PC, ZDA, GGA, GLL, RMC
timeMuxID = 12 // GPS mux channel - used for GPS Error
AISLocation = 3 // 1 = COM1, 2 = COM2, 3 = mux, default = 3
EnableAISParsing = 0 // 1 = no AIS data to FRM, default is 0
AISMuxID = 11 // MUX ID where AIS data is located; only read if AISLocation is 3
recordDuringPowerFail = 0 // To record NMEA during a power failure, set value to 1; default = 0
[ALARM]
Port = COM1
Baudrate = 4800 // default is 4800