Siemens SINAMICS G120D CU240D-2 DP - r8931[0...3] PN IP address actual; PN IP addr act; r8932[0...3] PN Default Gateway actual; PN Def Gateway act; r8933[0...3] PN Subnet Mask actual; PN Subnet Mask act; r8934 PN DHCP Mode actual; PN DHCP Mode act

SINAMICS G120D
List Manual (LH14), 01/2016, A5E33842313
431
2 Parameters
2.2 List of parameters
Description: Displays the actual IP address for the onboard PROFINET interface on the Control Unit.
Description: Displays the actual default gateway for the onboard PROFINET interface on the Control Unit.
Description: Displays the actual subnet mask for the onboard PROFINET interface on the Control Unit.
Description: Displays the actual DHCP mode for the onboard PROFINET interface on the Control Unit.
Value: 0: DHCP off
2: DHCP on, identification using MAC address
3: DHCP on, identification via name of station
Notice: When the DHCP mode is active (parameter value not equal to 0), PROFINET communication via this interface is no
longer possible! However, the interface can be used for commissioning tool such as STARTER or SCOUT.
Description: Displays the MAC address for the onboard PROFINET interface on the Control Unit.
Description: Displays the PROFINET Device Access Point ID (DAP ID) for the onboard PROFINET interface.
r8931[0...3] PN IP address actual / PN IP addr act
CU240D-2_PN
CU240D-2_PN_F
CU250D-2_PN_F
Access level: 3 Calculated: - Data type: Unsigned8
Can be changed: - Scaling: - Dyn. index: -
Unit group: - Unit selection: - Func. diagram: -
Min Max Factory setting
0 255 -
r8932[0...3] PN Default Gateway actual / PN Def Gateway act
CU240D-2_PN
CU240D-2_PN_F
CU250D-2_PN_F
Access level: 3 Calculated: - Data type: Unsigned8
Can be changed: - Scaling: - Dyn. index: -
Unit group: - Unit selection: - Func. diagram: -
Min Max Factory setting
0 255 -
r8933[0...3] PN Subnet Mask actual / PN Subnet Mask act
CU240D-2_PN
CU240D-2_PN_F
CU250D-2_PN_F
Access level: 3 Calculated: - Data type: Unsigned8
Can be changed: - Scaling: - Dyn. index: -
Unit group: - Unit selection: - Func. diagram: -
Min Max Factory setting
0 255 -
r8934 PN DHCP Mode actual / PN DHCP Mode act
CU240D-2_PN
CU240D-2_PN_F
CU250D-2_PN_F
Access level: 3 Calculated: - Data type: Integer16
Can be changed: - Scaling: - Dyn. index: -
Unit group: - Unit selection: - Func. diagram: -
Min Max Factory setting
0 3 -
r8935[0...5] PN MAC address / PN MAC addr
CU240D-2_PN
CU240D-2_PN_F
CU250D-2_PN_F
Access level: 3 Calculated: - Data type: Unsigned8
Can be changed: - Scaling: - Dyn. index: -
Unit group: - Unit selection: - Func. diagram: -
Min Max Factory setting
0000 hex 00FF hex -
r8939 PN DAP ID / PN DAP ID
CU240D-2_PN
CU240D-2_PN_F
CU250D-2_PN_F
Access level: 3 Calculated: - Data type: Unsigned32
Can be changed: - Scaling: - Dyn. index: -
Unit group: - Unit selection: - Func. diagram: -
Min Max Factory setting
- - -