Siemens SINAMICS G120D CU240D-2 DP - 2.4.4 Connector outputs (CO)

SINAMICS G120D
List Manual (LH14), 01/2016, A5E33842313
581
2 Parameters
2.4 BICO parameters (connectors/binectors)
r20356 BO: MFP 2 output Q / MFP 2 output Q
r20361 BO: MFP 3 output Q / MFP 3 output Q
2.4.4 Connector outputs (CO)
Product: SINAMICS G120D, Version: 4707900, Language: eng, Type: CO
r0021 CO: Actual speed smoothed / n_act smooth
r0025 CO: Output voltage smoothed / U_outp smooth
r0026 CO: DC link voltage smoothed / Vdc smooth
r0027 CO: Absolute actual current smoothed / I_act abs val smth
r0032 CO: Active power actual value smoothed / P_actv_act smth
r0034 CO: Motor utilization thermal / Mot_util therm
r0035 CO: Motor temperature / Mot temp
r0036 CO: Power unit overload I2t / PU overload I2t
r0037[0...19] CO: Power unit temperatures / PU temperatures
r0039[0...2] CO: Energy display / Energy displ
r0042[0...2] CO: Process energy display / Proc energy disp
r0060 CO: Speed setpoint before the setpoint filter / n_set before filt.
r0061[0...2] CO: Actual speed unsmoothed / n_act unsmoothed
r0062 CO: Speed setpoint after the filter / n_set after filter
r0063[0...2] CO: Speed actual value / n_act
r0064 CO: Speed controller system deviation / n_ctrl sys dev
r0066 CO: Output frequency / f_outp
r0067 CO: Output current maximum / I_outp max
r0068[0...1] CO: Absolute current actual value / I_act abs val
r0069[0...8] CO: Phase current actual value / I_phase act val
r0070 CO: Actual DC link voltage / Vdc act val
r0072 CO: Output voltage / U_output
r0074 CO: Modulat_depth / Mod_depth
r0075 CO: Current setpoint field-generating / Id_set
r0076 CO: Current actual value field-generating / Id_act
r0077 CO: Current setpoint torque-generating / Iq_set
r0078 CO: Current actual value torque-generating / Iq_act
r0079 CO: Torque setpoint / M_set
r0080[0...1] CO: Torque actual value / M_act
r0081 CO: Torque utilization / M_Utilization
r0082[0...2] CO: Active power actual value / P_act
r0083 CO: Flux setpoint / Flex setp
r0084[0...1] CO: Flux actual value / Flux act val
r0087 CO: Actual power factor / Cos phi act
r0094 CO: Transformation angle / Transformat_angle
r0289 CO: Maximum power unit output current / PU I_outp max
r0479[0...2] CO: Diagnostics encoder position actual value Gn_XIST1 / Diag Gn_XIST1
r0481[0...2] CO: Encoder status word Gn_ZSW / Enc Gn_ZSW
r0482[0...2] CO: Encoder actual position value Gn_XIST1 / Enc Gn_XIST1
r0483[0...2] CO: Encoder actual position value Gn_XIST2 / Enc Gn_XIST2
r0485[0...2] CO: Measuring gear encoder raw value incremental / Enc raw val incr
r0486[0...2] CO: Measuring gear encoder raw value absolute / Enc raw val abs
r0497[0...2] CO: Encoder diagnostic signal double word / Enc diag DW
r0498[0...2] CO: Encoder diagnostic signal low word / Enc diag low word
r0499[0...2] CO: Encoder diagnostic signal high word / Enc diag high word
r0586 CO: Measuring probe speed actual value / MT n_act
r0587 CO: Measuring probe measuring time measured / MT t_meas measured
r0588 CO: Measuring probe pulse counter / MT pulse counter