Rohde & Schwarz RTP044 - Page 847

Protocol analysis
R&S
®
RTP
847User Manual 1337.9952.02 ─ 12
You can define individual search parameters for the fields of the selected frame in the
table below the "Search criteria". To specify these parameters, select a field in the table
and define the data and/or index operators and values, or the bit state.
For a description of how to set the search conditions, see Chapter 13.19.3.1, "USB 3.1
trigger settings", on page 841.
Remote command:
SEARch:TRIGger:USBThree:ERENable on page 2072
SEARch:TRIGger:USBThree:ERRor<m>:ENABle on page 2072
SEARch:TRIGger:USBThree:FRENable on page 2072
SEARch:TRIGger:USBThree:FRAMe<m>:ENABle on page 2072
SEARch:TRIGger:USBThree:FIENable on page 2073
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:ENABle on page 2073
SEARch:TRIGger:USBThree:DOPerator on page 2073
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:DOPerator on page 2073
SEARch:TRIGger:USBThree:DMIN on page 2074
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:DMIN on page 2074
SEARch:TRIGger:USBThree:DMAX on page 2074
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:DMAX on page 2074
SEARch:TRIGger:USBThree:BIT on page 2075
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:BIT on page 2075
SEARch:TRIGger:USBThree:IOPerator on page 2075
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:IOPerator on page 2075
SEARch:TRIGger:USBThree:IMIN on page 2076
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:IMIN on page 2076
SEARch:TRIGger:USBThree:IMAX on page 2076
SEARch:TRIGger:USBThree:FRAMe<m>:FLD<n>:IMAX on page 2076
13.19.5.2 USB 3.1 search results
To get search results, "Enable" the search in the "Control" section of the "Search
Setup" dialog. You can minimize, shift or close the search dialog to better see the
"Search Results" table.
To get search results, "Enable" the search. You can minimize, shift or close the search
dialog.
The search results are listed in the search result table and marked in the waveform by
blue lines.
For an introduction to search results, see:
●
Chapter 11.1.2, "Search results", on page 449
●
Chapter 11.4.2, "Display zoom settings", on page 468
Remote commands:
●
SEARch:RESult:USBThree:FCOunt? on page 2078
●
SEARch:RESult:USBThree:FRAMe<m>:TYPE? on page 2077
●
SEARch:RESult:USBThree:FRAMe<m>:INFO? on page 2077
●
SEARch:RESult:USBThree:FRAMe<m>:STATe? on page 2078
USB 3.1 (option R&S
RTP-K61/K62)