Command and Drive Data Sets – Overview
Parameters
1-415
© Siemens AG 2009 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
p2177[0...n] Motor locked delay time / Mot lock t_del
p2178[0...n] Motor stalled delay time / Mot stall t_del
p2179[0...n] Output load identification current limit / Outp_ld iden I_lim
p2180[0...n] Delay time for missing output load / t_del no load
p2181[0...n] Load monitoring response / Load monit resp
p2182[0...n] Load monitoring speed threshold value 1 / n_thresh 1
p2183[0...n] Load monitoring speed threshold value 2 / n_thresh 2
p2184[0...n] Load monitoring speed threshold value 3 / n_thresh 3
p2185[0...n] Load monitoring torque threshold 1, upper / M_thresh 1 upper
p2186[0...n] Load monitoring torque threshold 1, lower / M_thresh 1 lower
p2187[0...n] Load monitoring torque threshold 2, upper / M_thresh 2 upper
p2188[0...n] Load monitoring torque threshold 2, lower / M_thresh 2 lower
p2189[0...n] Load monitoring torque threshold 3, upper / M_thresh 3 upper
p2190[0...n] Load monitoring torque threshold 3, lower / M_thresh 3 lower
p2192[0...n] Load monitoring delay time / Load monit t_del
p2193[0...n] Load monitoring configuration / Load monit config
p2194[0...n] Torque threshold value 2 / M_thresh val 2
p2195[0...n] Torque utilization switch-off delay / M_util t_off
p2196[0...n] Torque utilization scaling / M_util scal
p2201[0...n] CO: Technology controller, fixed value 1 / Tec_ctrl fix val 1
p2202[0...n] CO: Technology controller, fixed value 2 / Tec_ctrl fix val 2
p2203[0...n] CO: Technology controller, fixed value 3 / Tec_ctrl fix val 3
p2204[0...n] CO: Technology controller, fixed value 4 / Tec_ctrl fix val 4
p2205[0...n] CO: Technology controller, fixed value 5 / Tec_ctrl fix val 5
p2206[0...n] CO: Technology controller, fixed value 6 / Tec_ctrl fix val 6
p2207[0...n] CO: Technology controller, fixed value 7 / Tec_ctrl fix val 7
p2208[0...n] CO: Technology controller, fixed value 8 / Tec_ctrl fix val 8
p2209[0...n] CO: Technology controller, fixed value 9 / Tec_ctrl fix val 9
p2210[0...n] CO: Technology controller, fixed value 10 / Tec_ctrl fix val10
p2211[0...n] CO: Technology controller, fixed value 11 / Tec_ctrl fix val11
p2212[0...n] CO: Technology controller, fixed value 12 / Tec_ctrl fix val12
p2213[0...n] CO: Technology controller, fixed value 13 / Tec_ctrl fix val13
p2214[0...n] CO: Technology controller, fixed value 14 / Tec_ctrl fix val14
p2215[0...n] CO: Technology controller, fixed value 15 / Tec_ctrl fix val15
p2216[0...n] Technology controller fixed value selection method / Tec_ctr FixVal sel
p2230[0...n] Technology controller motorized potentiometer configuration / Tec_ctr mop config
p2237[0...n] Technology controller motorized potentiometer maximum value / Tec_ctrl mop max
p2238[0...n] Technology controller motorized potentiometer minimum value / Tec_ctrl mop min
p2240[0...n] Technology controller motorized potentiometer starting value / Tec_ctrl mop start
p2247[0...n] Technology controller motorized potentiometer ramp-up time / Tec_ctr mop t_r-up
p2248[0...n] Technology controller motorized potentiometer ramp-down time / Tec_ctrMop t_rdown
p2370[0...n] Staging enable / Staging enab
p2390[0...n] Hibernation starting speed / Hib n_Start
p2391[0...n] Hibernation delay time / Hib t_del
p2393[0...n] Hibernation restart speed relative w/o technology controller / Hib st. w/o Tec_c
p2394[0...n] Hibernation boost time period / Hib t_Boost
p2395[0...n] Hibernation boost speed / Hib n_Boost
p2396[0...n] Hibernation max. shutdown time / Hib t_shutd max
p2900[0...n] CO: Fixed value 1 [%] / Fixed value 1 [%]
p2901[0...n] CO: Fixed value 2 [%] / Fixed value 2 [%]
p2930[0...n] CO: Fixed value M [Nm] / Fixed value M [Nm]
p3231[0...n] Load monitoring speed deviation / Load monit n_dev
p3233[0...n] Torque actual value filter, time constant / M_act_filt T
To Next Page
Loading...
