Siemens CU230P-2 DP User Manual

Function diagrams Faults and warnings 2-582
© Siemens AG 2009 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
Fig. 2-129 8060 – Fault buffer
- 8060 -
Function diagram
87654321
FP_8060_97_51.vsd
Faults and warnings
G120 CU230P-2
29.10.2009 V4.3
Fault buffer
<1>
1
RESET
r0945 = 0
r0948 = 0
r0949 = 0
r2109 = 0
r2130 = 0
r2133 = 0
r2136 = 0
III
RESET
III
RESET
III
1 ms
POWER ON
<1>
1
[2546.7]
p2103 ... p2105
[2546.7]
p2106
[2546.7]
p2107
[2546.7]
p2108, p3110 ... p3112
[2548.2]
p3981
r0949[63] [I32]
r2133[63] [Float]
r0945[0]
r0945[1]
r0945[7]
r0945[56]
r0945[57]
r0945[63]
r0945[8]
r0945[9]
r0945[15]
r0949[0] [I32]
r2133[0] [Float]
r0949[1] [I32]
r2133[1] [Float]
r0949[7] [I32]
r2133[7] [Float]
r0949[56] [I32]
r2133[56] [Float]
r0949[57] [I32]
r2133[57] [Float]
r0949[8] [I32]
r2133[8] [Float]
r0949[9] [I32]
r2133[9] [Float]
r0949[15] [I32]
r2133[15] [Float]
r0948[0] [ms]
r2130[0] [d]
r0948[1] [ms]
r2130[1] [d]
r0948[7] [ms]
r2130[7] [d]
r0948[56] [ms]
r2130[56] [d]
r0948[57] [ms]
r2130[57] [d]
r0948[63] [ms]
r2130[63] [d]
r0948[8] [ms]
r2130[8] [d]
r0948[9] [ms]
r2130[9] [d]
r0948[15] [ms]
r2130[15] [d]
r2109[0] [ms]
r2136[0] [d]
r2109[1] [ms]
r2136[1] [d]
r2109[7] [ms]
r2136[7] [d]
r2109[56] [ms]
r2136[56] [d]
r2109[57] [ms]
r2136[57] [d]
r2109[63] [ms]
r2136[63] [d]
r2109[8] [ms]
r2136[8] [d]
r2109[9] [ms]
r2136[9] [d]
r2109[15] [ms]
r2136[15] [d]
1
<2>
<2>
32 bit counter,
free running
[8065.1]
Operating time
Acknowledge
faults
POWER ON
This fault is overwritten when "more recent" faults occur.
The buffer parameters are cyclically updated in the background (refer to the status signal in r2139).
Fault times
Actual
fault case
Faults
Acknowledging
1. Acknow-
ledged
fault case
7. Acknow-
ledged
fault case
[oldest]
Fault
Fault
2
Fault
8
1
Fault
Fault
2
Fault
8
1
Fault
Fault
2
Fault
8
Fault code
Fault value
Fault time
"come"
Fault time
"removed"
0 = "No fault present"
Fault case comes
Delete fault buffer
Fault goes
Fault comes
LED "RDY" [= red for fault]
Fault case acknowl.
Counter
16 bit
p0952 = 0:
Fault buffer is deleted/
cleared
Automatic
16 bit counter, free
running
Fault buffer change [8065.6]
Fault responses to the sequence control
t_System relative
0 ... 4294967295 [ms]
p0969 (0)
STW fault/alarm
r2138
r2138
.7
STW fault/alarm
r2138
r2138
.13
STW fault/alarm
r2138
r2138
.14
STW fault/alarm
r2138
r2138
.15
r2131
Actual fault code
ZSW fault/alarm 1
r2139
r2139
.3
Fault cases qty
0 ... 65535
p0952 (0)
r0944
Fault buff change

Siemens CU230P-2 DP Specifications

General

Brand	Siemens
Model	CU230P-2 DP
Category	Control Unit
Language	English