Siemens CU230P-2 DP User Manual

Signals and monitoring functions
Function diagrams
2-573
© Siemens AG 2009 All Rights Reserved SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
Fig. 2-121 8011 – Speed signals 2
- 8010 -
Function diagram
87654321
FP_8010_97_51.vsd
Signals and monitoring functions
G120 CU230P-2
29.10.2009 V4.3
Speed signals 1
0
1
[8011.2]
[8012.5]
[8013.1]
[6730.1]
[6731.1]
[3050.8]
0
1
0
1
0
1
0
1
[2537.3]
T0
[2534.3]
<1>
<1>
n
n
0
From setpoint limiting
F07901 "motor overspeed"
Smoothing
Calculated
r0063
n_act [1/min]
r0063
n_act [1/min]
r2169
n_act smth message [1/min]
Hyst n_act>n_max
0.00 ... 60000.00 [1/min]
p2162 [D] (0.00)
ZSW monitor 1
r2197
r2197
.6
ZSW monitor 3
r2199
r2199
.1
t_on cmpr val rchd
0.0 ... 10000.0 [ms]
p2156 [D] (0.0)
ZSW monitor 1
r2197
r2197
.1
ZSW monitor 1
r2197
r2197
.2
ZSW monitor 3
r2199
r2199
.0
n_thresh val 2
0.00 ... 210000.00 [1/min]
p2155 [D] (900.00)
n_thresh val 1
0.00 ... 210000.00 [1/min]
p2141 [D] (5.00)
n_hysteresis 1
0.00 ... 300.00 [1/min]
p2142 [D] (2.00)
n_act_filt T
0 ... 1000000 [ms]
p2153 [D] (0)
T0
t_on cmpr val rchd
0.0 ... 10000.0 [ms]
p2156 [D] (0.0)
0
1
Monit config
p2149
T0
[2534.3]
0
1
0
1
n_thresh val 2
0.00 ... 210000.00 [1/min]
p2155 [D] (900.00)
.3
<1>
<1>
r1084
n_limit pos eff [1/min]
r1087
n_limit neg eff [1/min]
n_hysteresis 2
0.00 ... 300.00 [1/min]
p2140 [D] (90.00)
n_hysteresis 2
0.00 ... 300.00 [1/min]
p2140 [D] (90.00)
0
1
n_hysteresis 3
0.00 ... 300.00 [1/min]
p2150 [D] (2.00)
n_thresh val 3
0.00 ... 210000.00 [1/min]
p2161 [D] (5.00)
[0]
[1]
[6799.4]
1
t_on cmpr val rchd
0.0 ... 10000.0 [ms]
p2156 [D] (0.0)
|n_act| < speed threshold value 3
f or n comparison value
reached or exceeded
|n_act| <= speed threshold value 2
|n_act| > speed threshold value 2
|n_act| > n_max
[2537.3]
[2534.3]
<1>

Siemens CU230P-2 DP Specifications

General

Brand	Siemens
Model	CU230P-2 DP
Category	Control Unit
Language	English