Siemens CU230P-2 DP - Fig. 2-130 8065 - Warning buffer

Faults and warnings
Function diagrams
2-583
© Siemens AG 2009 All Rights Reserved SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
Fig. 2-130 8065 – Warning buffer
- 8065 -
Function diagram
87654321
FP_8065_97_51.vsd
Faults and warnings
G120 CU230P-2
29.10.2009 V4.3
Warning buffer
RESET
1
r2122 = 0
r2123 = 0
r2124 = 0
r2125 = 0
r2134 = 0
r2145 = 0
r2146 = 0
1
III
RESET
III
RESET
III
RESET
1
POWER ON
POWER ON
[2548.2]
[2546.7]
p2112
[2546.7]
p2116
[2546.7]
p2117
r2122[0]
r2122[1]
r2122[7]
r2124[0] [I32]
r2134[0] [Float]
r2124[1] [I32]
r2134[1] [Float]
r2124[7] [I32]
r2134[7] [Float]
r2123[0] [ms]
r2145[0] [d]
r2123[1] [ms]
r2145[1] [d]
r2123[7] [ms]
r2145[7] [d]
r2125[0] [ms]
r2146[0] [d]
r2125[1] [ms]
r2146[1] [d]
r2125[7] [ms]
r2146[7] [d]
[8060.1]
POWER ON
r2122[8]
r2122[9]
r2122[63]
r2124[8] [I32]
r2134[8] [Float]
r2124[9] [I32]
r2134[9] [Float]
r2124[63] [I32]
r2134[63] [Float]
r2123[8] [ms]
r2145[8] [d]
r2123[9] [ms]
r2145[9] [d]
r2123[63] [ms]
r2145[63] [d]
r2125[8] [ms]
r2146[8] [d]
r2125[9] [ms]
r2146[9] [d]
r2125[63] [ms]
r2146[63] [d]
<1>
<1>
Operating time
The buffer parameters are updated cyclically in the background (see status signal in r2139).
Alarm times
Alarm 1
(oldest)
Alarm 2
Alarm 8
(most
recent)
Alarm history
Alarm 1
(most recent)
Alarm 2
Alarm 56
(oldest)
Alarm code
Alarm value
Alarm time
"come"
Alarm time
"removed"
0 = "No alarm present"
Fault buffer change [8060.8]
Alarm comes
Alarm goes
Delete alarm
buffer
Alarms
counter
p2111
p2111 = 0:
Alarm buffer is deleted
16 bit counter,
free running
16 bit counter,
free running
Alarm comes
Delete alarm buffer
Counter
16 bit
STW fault/alarm
r2138
r2138
.10
STW fault/alarm
r2138
r2138
.11
STW fault/alarm
r2138
r2138
.12
r2132
Actual alarm code
ZSW fault/alarm 1
r2139
r2139
.7
Alarm number
r2110
r2120
Sum buffer changed
r2121
Alrm buff changed