Connector/Binector (BICO)-Parameters
Parameters
1-423
© Siemens AG 2009 All Rights Reserved
SINAMICS G120 Control Units CU230P-2 Parameter Manual (LH9), 11/2009
p11098 CI: Free tec_ctrl 0 limit minimum signal source / Ftec0 lim min s_s
p11099 CI: Free tec_ctrl 0 limit offset signal source / Ftec0 lim offs
p11153 CI: Free tec_ctrl 1 setpoint signal source / Ftec1 setp s_s
p11164 CI: Free tec_ctrl 1 actual value signal source / Ftec1 act v s_s
p11197 CI: Free tec_ctrl 1 limit maximum signal source / Ftec1 lim max s_s
p11198 CI: Free tec_ctrl 1 limit minimum signal source / Ftec1 lim min s_s
p11199 CI: Free tec_ctrl 1 limit offset signal source / Ftec1 lim offs
p11253 CI: Free tec_ctrl 2 setpoint signal source / Ftec2 setp s_src
p11264 CI: Free tec_ctrl 2 actual value signal source / Ftec2 act v s_s
p11297 CI: Free tec_ctrl 2 limit maximum signal source / Ftec2 lim max s_s
p11298 CI: Free tec_ctrl 2 limit minimum signal source / Ftec2 lim min s_s
p11299 CI: Free tec_ctrl 2 limit offset signal source / Ftec2 lim offs
p20094[0...3] CI: ADD 0 inputs / ADD 0 inputs
p20098[0...3] CI: ADD 1 inputs / ADD 1 inputs
p20102[0...1] CI: SUB 0 inputs / SUB 0 inputs
p20106[0...1] CI: SUB 1 inputs / SUB 1 inputs
p20110[0...3] CI: MUL 0 inputs / MUL 0 inputs
p20114[0...3] CI: MUL 1 inputs / MUL 1 inputs
p20118[0...1] CI: DIV 0 inputs / DIV 0 inputs
p20123[0...1] CI: DIV 1 inputs / DIV 1 inputs
p20128 CI: AVA 0 input X / AVA 0 input X
p20133 CI: AVA 1 input X / AVA 1 input X
p20218[0...1] CI: NSW 0 inputs / NSW 0 inputs
p20223[0...1] CI: NSW 1 inputs / NSW 1 inputs
p20228 CI: LIM 0 input X / LIM 0 input X
p20236 CI: LIM 1 input X / LIM 1 input X
p20244[0...1] CI: PT1 0 inputs / PT1 0 inputs
p20250[0...1] CI: PT1 1 inputs / PT1 1 inputs
p20256[0...1] CI: INT 0 inputs / INT 0 inputs
p20266 CI: LVM 0 input X / LVM 0 input X
p20275 CI: LVM 1 input X / LVM 1 input X
p20284 CI: DIF 0 input X / DIF 0 input X
p20308[0...3] CI: ADD 2 inputs / ADD 2 inputs
p20312[0...1] CI: NCM 0 inputs / NCM 0 inputs
p20318[0...1] CI: NCM 1 inputs / NCM 1 inputs
p20372 CI: PLI 0 input X / PLI 0 input X
p20378 CI: PLI 1 input X / PLI 1 input X
p31023[0...3] CI: Multi-zone control setpoint input / Zone_ctrl setp inp
p31026[0...2] CI: Multi-zone control actual-value input / Zon_ctrl act inp
To Next Page
Loading...
Need help?
General
